In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: revalidate LOAD_CONN_PARAM queued update
MGMT_OP_LOAD_CONN_PARAM queues conn_update_sync() when a single parameter
update changes an existing LE central connection. The queued work currently
stores a borrowed hci_conn_params entry from hdev->le_conn_params. A later
LOAD_CONN_PARAM request can clear disabled parameters and free that entry
before hci_cmd_sync_work() runs the queued callback.
Do not keep the borrowed hci_conn_params pointer in queued work. Queue the
hci_conn instead and hold a reference until the queued callback completes.
When the work runs,
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: extend conn_hash lookup critical sections
Using RCU-protected pointers outside the critical sections without
refcount is incorrect and may result to UAF.
Extend critical section to cover both hci_conn_hash lookup and use of
the returned conn.
Add surrounding rcu_read_lock() also when return value is not used, in
preparation for RCU lockdep requirement to hci_lookup_le_connect().
This avoids concurrent deletion of the conn before we are done
dereferencing it.
Also, make sure to hold hdev->lock when accessing hdev->accept_list.
Bluetooth: mgmt: fix locking in unpair_device/disconnect_sync
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: mgmt: fix locking in unpair_device/disconnect_sync
Dereferencing RCU-protected pointers outside critical sections is
invalid and may lead to UAF.
Take hdev->lock for hci_conn lookup and hci_abort_conn(). Don't use RCU
to ensure the conn is fully initialized at this point.
Bluetooth: mgmt: hold reference for hci_conn in mgmt_pending_cmds
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: mgmt: hold reference for hci_conn in mgmt_pending_cmds
Dereferencing RCU-protected pointers outside critical sections is
invalid and may lead to UAF. Use of hci_conn in hci_sync callbacks also
needs to hold refcount to avoid UAF.
Take appropriate locks for hci_conn lookups, and take refcount for
hci_conn pointers stored in mgmt_pending_cmd so that the pointer stays
valid.
When accessing conn->state, ensure hdev->lock is held to avoid data
race.
Bluetooth: hci_qca: Clear memdump state on invalid dump size
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_qca: Clear memdump state on invalid dump size
qca_controller_memdump() allocates qca->qca_memdump before processing
the first dump packet. For a sequence-zero packet it then disables IBS,
marks memdump collection active, and reads the advertised dump size.
If the controller reports a zero dump size, the error path frees the
local qca_memdump object and returns without clearing qca->qca_memdump
or undoing the collection state. A later memdump work item initializes
its local pointer from qca->qca_memdump and skips allocation when that
pointer is non-NULL, so i
smb/client: handle overlapping allocated ranges in fallocate
In the Linux kernel, the following vulnerability has been resolved:
smb/client: handle overlapping allocated ranges in fallocate
smb3_simple_fallocate_range() can skip holes when an allocated range
returned by the server starts before the current fallocate offset. The
skipped hole is not zero-filled, but fallocate still returns success. A
later write to that hole may therefore fail with ENOSPC.
The function queries allocated ranges so that it can preserve existing
contents and write zeroes only into holes. However, the server may return
a range that starts before the current fallocate offset.
For example, assume the fallocate request is [
bpf, sockmap: Reject unhashed UDP sockets on sockmap update
In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Reject unhashed UDP sockets on sockmap update
UDP sockets get SOCK_RCU_FREE set when (auto-)bound. This means
sk_is_refcounted(unbound) = true, while sk_is_refcounted(bound) = false.
Because sockmap accepts unbound UDP sockets, a BPF program can increment a
socket's refcount via lookup. If the socket is subsequently bound, the
transition from unbound to bound causes bpf_sk_release() to skip the
decrement of the refcount, causing a memory leak.
unreferenced object 0xffff88810bc2eb40 (size 1984):
comm "test_progs", pid 2451, jiffies 4295320596
hex dump (fi
s390/checksum: Fix csum_partial() without vector facility
In the Linux kernel, the following vulnerability has been resolved:
s390/checksum: Fix csum_partial() without vector facility
Currently csum_partial() calls csum_copy() with copy=false and dst=NULL.
On machines without the vector facility, csum_copy() falls back to
cksm(dst, ...), causing the checksum to be calculated from address zero
instead of the source buffer.
The VX implementation already checksums data loaded from src. Make the
fallback do the same by passing src to cksm().
In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Keep scheduler timeline name alive
The scheduler keeps a pointer to the timeline name, but q->name
is freed with the exec queue while scheduler fences can still
reference it.
Store the name in struct xe_guc_exec_queue so it shares
the scheduler's RCU-deferred lifetime.
(cherry picked from commit 41075f0eb5dcbd3b065d15f15ef7bbe9315188e8)
drm/xe/guc: Hold device ref until queue teardown completes
In the Linux kernel, the following vulnerability has been resolved:
drm/xe/guc: Hold device ref until queue teardown completes
GuC exec queue destruction can run asynchronously. If the final device
put happens from a destroy worker, drmm cleanup can end up draining
the same workqueue and deadlock.
Hold a drm_device reference for the queue lifetime and drop it after
queue teardown completes. This keeps drmm cleanup from running while
async destroy work is still pending.
Move GuC destroy work to a module-lifetime Xe workqueue and flush it
on PCI remove so hot-unbind/rebind still waits for pending destroy work.
With queue-held device refs,
ksmbd: pin conn during async oplock break notification
In the Linux kernel, the following vulnerability has been resolved:
ksmbd: pin conn during async oplock break notification
smb2_oplock_break_noti() and smb2_lease_break_noti() store a ksmbd_conn
pointer in an async ksmbd_work and then queue that work on ksmbd-io. The
work only increments conn->r_count, which prevents teardown from passing
the pending-request wait after the increment, but it does not pin the
struct ksmbd_conn object.
If connection teardown races with an oplock break notification, the last
conn reference can be dropped before the queued worker finishes. The
worker then uses the freed conn in ksmbd_conn_write() and
ksmbd_co
net/sched: act_tunnel_key: Defer dst_release to RCU callback
In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_tunnel_key: Defer dst_release to RCU callback
Fix a race-condition use-after-free in tunnel_key_release_params().
The function releases the metadata_dst of the old params synchronously
via dst_release() while deferring the params struct free with
kfree_rcu(). A concurrent tunnel_key_act() reader on the datapath may
still hold the old params pointer (under rcu_read_lock_bh) and proceed
to call dst_clone(¶ms->tcft_enc_metadata->dst) after the writer's
dst_release has already pushed the dst's rcuref to RCUREF_DEAD.
[email protected] produced a
sctp: fix auth_hmacs array size in struct sctp_cookie
In the Linux kernel, the following vulnerability has been resolved:
sctp: fix auth_hmacs array size in struct sctp_cookie
The auth_hmacs array in struct sctp_cookie is supposed to store a complete
SCTP_AUTH_HMAC_ALGO parameter, which consists of a struct sctp_paramhdr
followed by N HMAC identifiers.
However, the array size was calculated using an extra 2 bytes instead of
sizeof(struct sctp_paramhdr), which is 4 bytes. When four HMAC identifiers
are configured, the HMAC-ALGO parameter stored in the endpoint is larger
than the auth_hmacs buffer in the cookie.
As a result, sctp_association_init() copies beyond the end of auth_hmacs
when init
In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Handle partially initialized auxiliary devices
bnxt_aux_devices_init() calls auxiliary_device_init() before all fields
used by bnxt_aux_dev_release() are initialized. After
auxiliary_device_init() succeeds, later errors must unwind with
auxiliary_device_uninit(), which invokes the release callback.
The release callback assumes that aux_priv->id, aux_priv->edev,
edev->net and edev->ulp_tbl are all populated. If allocation fails
after auxiliary_device_init(), the release path can otherwise dereference
or clear partially initialized state.
Allocate and attach the
usb: core: sysfs: add lock to bos_descriptors_read()
In the Linux kernel, the following vulnerability has been resolved:
usb: core: sysfs: add lock to bos_descriptors_read()
Add a lock to the function bos_descriptors_read().
This function accesses udev->bos, which could be simultaneously freed in
usb_reset_and_verify_device(), a function that is commonly called in
drivers all over the kernel.
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
In the Linux kernel, the following vulnerability has been resolved:
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning
usb: core: port: Deattach Type-C connector on component unbind
In the Linux kernel, the following vulnerability has been resolved:
usb: core: port: Deattach Type-C connector on component unbind
connector_unbind() is the mirror of connector_bind(), but it is missing
the symmetric call to typec_deattach() that connector_bind() makes via:
if (port_dev->child)
typec_attach(port_dev->connector, &port_dev->child->dev);
When a Thunderbolt dock is unplugged, two teardown paths race:
1. The component framework calls connector_unbind() first, which sets
port_dev->connector = NULL without calling typec_deattach(). This
leaves port->usb2_dev/port->usb3_dev in struct typec_port pointing at
usb: musb: omap2430: Do not put borrowed of_node in probe
In the Linux kernel, the following vulnerability has been resolved:
usb: musb: omap2430: Do not put borrowed of_node in probe
omap2430_probe() stores pdev->dev.of_node in a local np variable. This is
a borrowed pointer and the probe function does not take a reference to
it.
The success and error paths nevertheless call of_node_put(np). This drops
a reference that is owned by the platform device, and can leave
pdev->dev.of_node with an unbalanced reference count.
Do not put the borrowed platform device node from omap2430_probe().
References taken for the child MUSB device are handled by the device core,
and the ctrl-module phandle referenc
usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: dummy_hcd: prevent fifo_req reuse during giveback
dummy_hcd embeds a single shared usb_request (dum->fifo_req) that the
"emulated single-request FIFO" fast-path in dummy_queue() reuses for
small IN transfers: it copies the caller's request into it
(req->req = *_req) and queues it, treating list_empty(&fifo_req.queue)
as "the slot is free".
The completion side (dummy_timer/transfer/nuke/dummy_dequeue) follows
the standard pattern: list_del_init(&req->queue) unlinks the request,
then the lock is dropped and usb_gadget_giveback_request() invokes
req->complete().
usb: gadget: printer: fix infinite loop in printer_read()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: printer: fix infinite loop in printer_read()
printer_read() uses the same variable for the requested copy size and
the number of bytes actually copied to user space. copy_to_user()
returns the number of bytes not copied, so when it fails to copy
anything, the computed copied length becomes zero.
In that case len, buf, current_rx_bytes and current_rx_buf are left
unchanged. If RX data is available and the user buffer remains
unwritable, the read loop can repeat indefinitely.
Track the copied length separately and return -EFAULT, or the number of
bytes already