In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: clear forceRM when issuing EndTransfer
The forceRM bit of the DEPCMD register controls the behavior of the
EndTransfer command used to stop an active transfer. Older DWC3
programming guide revisions recommended setting forceRM=1 when
issuing EndTransfer. Newer programming guide revisions recommend
issuing EndTransfer with forceRM cleared.
With forceRM=1 on DWC_usb31 v2.00a and v2.10a controllers, a transfer
aborted through the ep_dequeue path was observed to remain active
after EndTransfer completion. A subsequent StartTransfer issued on the
same endpoint trigge
usb: storage: realtek_cr: fix use-after-free on disconnect
In the Linux kernel, the following vulnerability has been resolved:
usb: storage: realtek_cr: fix use-after-free on disconnect
realtek_cr_destructor() calls timer_delete() before the chip containing
the timer is freed. The timer callback may still be running and can
rearm itself, resulting in a use-after-free.
Use timer_shutdown_sync() to wait for the callback and prevent further
rearming. Do this unconditionally because ss_en may be changed after
the timer is armed.
Move timer_setup() into init_realtek_cr() so the timer is initialized
before any failure path can invoke the destructor.
Found by static analysis.
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
cc_debounce_dwork is queued from the set_cc() and start_toggling()
callbacks, which run from TCPM's kthread worker. port_stop() returns
before tcpm_unregister_port() destroys that worker. Flushing the worker
during unregister may therefore run a callback which queues the delayed
work after port_stop() has returned.
The delayed work can then run after devres has freed pmic_typec_port.
Use disable_delayed_work_sync() in port_stop() to cancel a pending
instance and prevent the TCPM callbacks from queueing anoth
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic: cancel reset_work on stop
pdphy_stop() disables IRQs but leaves reset_work pending. If the IRQ
handler schedules it just before disable_irq(), the work runs after
remove() frees the struct via devm.
Call cancel_work_sync() after disabling IRQs to close the window.
This issue was found by an in-house static analysis tool.
usb: typec: ucsi: displayport: Fix OOB altmode array index
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: displayport: Fix OOB altmode array index
The UCSI displayport driver indexes the connector's port altmode array
with the GET_CURRENT_CAM response after checking it is not 0xff. The
port altmode array is UCSI_MAX_ALTMODES elements long. If the PPM
returns an invalid GET_CURRENT_CAM response above UCSI_MAX_ALTMODES and
not equal to 0xff, the kernel may crash with an array index OOB error.
Update the UCSI displayport driver to verify the current cam is less
than UCSI_MAX_ALTMODES before accessing the port altmode array.
usb: gadget: midi2: Fix null-pointer dereference in f_midi2_free_ep_reqs
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: midi2: Fix null-pointer dereference in f_midi2_free_ep_reqs
A null-pointer dereference occurs in f_midi2_free_ep_reqs() when attempting
to clean up an endpoint that was never initialized.
When configuring the MIDI 2.0 gadget via configfs and setting the block
direction to SNDRV_UMP_DIR_INPUT, the initialization of the midi1_ep_out
endpoint is explicitly skipped during the gadget bind phase
(f_midi2_bind()). As a result, the usb_ep->card field remains NULL.
Later, when the host sets the alternate setting, f_midi2_set_alt()
unconditionally stops both the IN and
usb: gadget: f_mass_storage: fix null pointer dereference in fsg_common_set_num_buffers()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_mass_storage: fix null pointer dereference in fsg_common_set_num_buffers()
Previously fsg_num_buffers_validate() was removed as it was not
necessary due to Kconfig setting the limits for n from 2 to 256 with
default as 2. However, setting the page content in such a way that
kstrtou8() reflects n value as either 0 or 1 bypasses these
restrictions leading to a null pointer dereference if n is 0. Fix
this by adding a check for n < 2 and returning -EINVAL if n is
either 0 or 1 consistent with Kconfig logic.
usb: gadget: f_midi2: fix use-after-free in string attribute show path
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi2: fix use-after-free in string attribute show path
f_midi2_opts_str_show() takes the string lock internally, but its
callers dereference the opts->info.<field> pointer before calling it,
outside the lock. This races with f_midi2_opts_str_store(), which
frees the old string under opts->lock when the attribute is written
concurrently, the show path can read a pointer that gets freed
before the lock inside str_show() is even taken.
Change f_midi2_opts_str_show() to take a pointer to the string field,
matching the existing pattern in f_midi2_opts_str_store(
usb: gadget: f_midi: initialize work in f_midi_alloc()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi: initialize work in f_midi_alloc()
f_midi_alloc initializes free_ref to 1 and it can only be incremented
when a sound card is registered via f_midi_register_card().
f_midi_register_card() is only called in f_midi_bind() which actually
performs INIT_WORK. If f_midi_bind() is never run, work is not
initialized and the if condition in f_midi_free becomes true,
this results in a warning later in __flush_work as work->func = 0.
Fix this by moving INIT_WORK from f_midi_bind() to f_midi_alloc().
USB: gadget: fix NULL pointer dereference in gadget_dev_ioctl()
In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: fix NULL pointer dereference in gadget_dev_ioctl()
gadget_dev_ioctl() reads dev->gadget before acquiring dev->lock, but
dev->state is checked after acquiring the lock. Therefore a concurrent
bind can change the device state between these operations, which can
leave ioctl with a stale NULL gadget pointer and causing a NULL pointer
dereference at gadget->ops->ioctl.
Read dev->gadget while holding dev->lock so that the gadget pointer
and device state are sampled consistently.
usb: gadget: fix null pointer dereference in usb_put_function_instance()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: fix null pointer dereference in usb_put_function_instance()
usb_put_function_instance() attempts to dereference fd inside fi struct
to get mod in uvc_alloc_inst() error path. However, fd is not allocated
until later in try_get_usb_function_instance() after allocating fi in
uvc_alloc_inst() and thus guranteed to be null in error path. Fix this
by adding a null check for fi->fd that returns if fd is null.
staging: rtl8723bs: fix OOB read / stack overflow in rtw_get_wps_attr()
In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read / stack overflow in rtw_get_wps_attr()
rtw_get_wps_attr() walks WPS attributes inside a WPS IE taken from
a wireless management frame. For each candidate attribute it only
checks that the fixed 4-byte attribute header (2-byte ID + 2-byte
length) fits inside the IE:
if (attr_ptr + 4 > wps_ie + wps_ielen)
break;
u16 attr_id = get_unaligned_be16(attr_ptr);
u16 attr_data_len = get_unaligned_be16(attr_ptr + 2);
u16 attr_len = attr_data_len + 4;
attr_data_len (and therefore attr_len) is read directly from the
wire and is never checked agai
staging: rtl8723bs: fix OOB read in rtw_action_frame_parse()
In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_action_frame_parse()
rtw_action_frame_parse() takes a frame_len parameter but never
actually checks it before indexing into the frame body:
const u8 *frame_body = frame + sizeof(struct ieee80211_hdr_3addr);
...
c = frame_body[0];
...
a = frame_body[1];
frame_body already points 24 bytes (sizeof(struct
ieee80211_hdr_3addr)) into frame, so reading frame_body[0] and
frame_body[1] requires frame_len >= 26. A management action frame
shorter than that (e.g. exactly 24 bytes, the minimum a malicious
peer can send) causes a 1-2 byte ou
staging: rtl8723bs: fix OOB read in rtw_restruct_wmm_ie()
In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix OOB read in rtw_restruct_wmm_ie()
rtw_restruct_wmm_ie() scans in_ie for a WMM IE with:
while (i < in_len) {
...
if (i + 5 < in_len && in_ie[i] == 0xDD && ...) {
...
break;
}
i += (in_ie[i + 1] + 2); /* to the next IE element */
}
When the "i + 5 < in_len" match check fails simply because i is
within 5 bytes of the end of the buffer (i.e. no WMM IE was found
near the tail of in_ie), execution falls through to
"i += (in_ie[i + 1] + 2)", which reads in_ie[i + 1]. If i == in_len
- 1 at that point, this is a 1-byte out-of-bounds read of
xhci: fix lost bounce buffers on TDs spanning several ring segments
In the Linux kernel, the following vulnerability has been resolved:
xhci: fix lost bounce buffers on TDs spanning several ring segments
When a TD reaches a link TRB with data that is not aligned to the
endpoint's wMaxPacketSize, xhci_align_td() stages the unalignable tail
through the bounce buffer of the ring segment holding that link TRB.
xhci_unmap_td_bounce_buffer() later unmaps it and, for IN transfers,
copies the data back into the URB's buffer.
The enqueue path records the segment that was bounced in td->bounce_seg,
under the assumption that a TD never spans more than two ring segments.
That assumption does not hold: a TD large enoug
tracing: Take trace_array reference when opening options file
In the Linux kernel, the following vulnerability has been resolved:
tracing: Take trace_array reference when opening options file
The options files do not take the trace_array reference for the options
they represent. This could cause a use-after-free kernel crash if one of
these files is opened by one task and another task removes the instance
that the option is for. Because it doesn't take a reference upon opening,
it will not stop the removal which will free the options descriptor that
is being used.
As the options are somewhat dynamic in their creation at boot up, each
file represents a flag in the trace_array. The trace_array has an a
spi: Fix DMA mapping ownership on partial map failure
In the Linux kernel, the following vulnerability has been resolved:
spi: Fix DMA mapping ownership on partial map failure
If RX mapping fails after TX mapping succeeds, __spi_map_msg() unmaps
TX but leaves tx_sg_mapped set. If TX mapping fails on a later
transfer, mappings created for earlier transfers remain active.
In both cases, cur_{tx,rx}_dma_dev have not yet been updated because they
are assigned only after every transfer has been mapped. The subsequent
spi_unmap_msg() may therefore unmap the TX mapping again or release
earlier mappings using a NULL or stale device. Using a NULL device can
trigger an oops. An empty SG table does not
scsi: target: iscsi: Reserve a terminator byte for the login payload
In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Reserve a terminator byte for the login payload
iscsi_target_check_login_request() rejects a login PDU whose
DataSegmentLength exceeds MAX_KEY_VALUE_PAIRS, but the test is '>' and
login->req_buf is allocated with exactly MAX_KEY_VALUE_PAIRS
bytes. Since iscsit_get_login_rx() receives payload_length + padding
bytes, where
padding = ((-payload_length) & 3);
any payload_length from 8189 to 8192 fills the whole 8192 byte
buffer. The write stays in bounds, but no byte is left for a NUL
terminator.
The buffer is subsequently consumed as a C string. In the
scsi: pm8001: Use rollback index when freeing MSI-X vectors
In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Use rollback index when freeing MSI-X vectors
pm8001_request_msix() unwinds previously registered handlers with
free_irq() when request_irq() fails. The rollback loop uses the failing
index i for every iteration instead of the already registered vector
index j.
That passes the wrong IRQ/dev_id pair to free_irq() and leaves the
earlier handlers installed. Use j for both pci_irq_vector() and the
matching irq_vector entry in the rollback loop.
futex: Prevent rcuwait use-after-free during requeue PI
In the Linux kernel, the following vulnerability has been resolved:
futex: Prevent rcuwait use-after-free during requeue PI
On PREEMPT_RT, FUTEX_CMP_REQUEUE_PI can trigger a KASAN report
(slab-out-of-bounds) in futex_requeue_pi_complete() invocation of
rcuwait_wake_up().
The futex_q used by futex_wait_requeue_pi() is allocated on the waiter's
stack. An early wakeup can race with a PI requeue as follows:
waiter requeue task
------ ------------
futex_wait_requeue_pi()
futex_do_wait()
schedule()
futex_requeue