Vulnerabilidades de linux · Página 98

media: rtl2832_sdr: release URBs and stream buffers on start_streaming() failure

In the Linux kernel, the following vulnerability has been resolved: media: rtl2832_sdr: release URBs and stream buffers on start_streaming() failure rtl2832_sdr_start_streaming() calls rtl2832_sdr_alloc_stream_bufs(), rtl2832_sdr_alloc_urbs() and rtl2832_sdr_submit_urbs() in sequence and shares a single err: label that only unlocks the mutex and returns. When alloc_urbs() succeeds but submit_urbs() fails, or when alloc_urbs() itself returns -ENOMEM after alloc_stream_bufs() has already succeeded, the URBs and/or the coherent DMA stream buffers stay allocated while streaming reports failure to vb2. Two latent defects follow on the next VIDIO

• Actualiza a 6.12.111-1

media: s2255: bound JPEG frame size before copying into the buffer

In the Linux kernel, the following vulnerability has been resolved: media: s2255: bound JPEG frame size before copying into the buffer s2255_fillbuff() memcpy()s vc->jpg_size bytes of a captured JPEG/MJPEG frame into the vb2 plane. vc->jpg_size is taken verbatim from the S2255_MARKER_FRAME header the device sends (pdword[4] in save_frame()) and, unlike the frame payload length just above it, is never bounded: payload = le32_to_cpu(pdword[3]); if (payload > vc->req_image_size) /* payload is checked ... */ return -EINVAL; vc->pkt_size = payload; vc->jpg_size = le32_to_cpu(pdword[4]); /* ... jpg_size is not */ A malicious or malfuncti

• Actualiza a 6.12.111-1

media: s2255: check firmware size before reading trailing marker

In the Linux kernel, the following vulnerability has been resolved: media: s2255: check firmware size before reading trailing marker s2255_probe() reads a 4-byte marker and version from the last 8 bytes of the firmware blob (fw->data[fw_size - 8] and [fw_size - 4]). If the firmware file is shorter than 8 bytes, fw_size - 8 underflows and the access reads out of bounds. Validate the firmware size before indexing.

• Actualiza a 6.12.111-1

media: saa7164: fix cleanup on resource allocation failure

In the Linux kernel, the following vulnerability has been resolved: media: saa7164: fix cleanup on resource allocation failure saa7164_dev_setup() adds the device to the global saa7164_devlist before requesting the PCI BAR memory regions. If get_resources() fails, saa7164_dev_setup() decrements the device count and returns an error, but leaves the device on saa7164_devlist. The probe error path then frees the device, leaving a dangling entry on the global list. Reuse the existing MMIO mapping error path to remove the device from saa7164_devlist and decrement the device count before returning. Also release BAR0 if it was successfully requ

• Actualiza a 6.12.111-1

media: tda18250: fix possible integer overflow

In the Linux kernel, the following vulnerability has been resolved: media: tda18250: fix possible integer overflow Integer overflow may occur, when variable exp equals to zero. Result of shift 1 << (exp - 1) may then leads to undefined behavior.

• Actualiza a 6.12.111-1

media: v4l2-async: avoid deleting unlinked ASC entry on link error

In the Linux kernel, the following vulnerability has been resolved: media: v4l2-async: avoid deleting unlinked ASC entry on link error v4l2_async_match_notify() creates ancillary media links before adding asc->asc_subdev_entry to sd->asc_list. If ancillary link creation fails, the function jumps to err_call_unbind while asc_subdev_entry has not been linked yet. Async connections are zero-allocated, so the list entry still has NULL next and prev pointers on this path. Calling list_del() on it can therefore dereference NULL instead of returning the original link creation error. Do not delete asc_subdev_entry from err_call_unbind. There is n

• Actualiza a 6.12.111-1

media: v4l2-fwnode: Fix fwnode leak in v4l2_fwnode_parse_link

In the Linux kernel, the following vulnerability has been resolved: media: v4l2-fwnode: Fix fwnode leak in v4l2_fwnode_parse_link In v4l2_fwnode_parse_link(), the remote endpoint fwnode reference is acquired using fwnode_graph_get_remote_endpoint(). This reference is properly released in the error paths, but it is leaked on the success path. Add the missing fwnode_handle_put() before returning 0 to prevent the reference leak. [Sakari Ailus: Fix subject prefix and coding style a little.]

• Actualiza a 6.12.111-1

media: video-i2c: fix kthread error pointer left in kthread_vid_cap on failure

In the Linux kernel, the following vulnerability has been resolved: media: video-i2c: fix kthread error pointer left in kthread_vid_cap on failure kthread_run() returns an ERR_PTR on failure, not NULL. When start_streaming() fails, data->kthread_vid_cap is left holding this error pointer instead of being cleared. This causes two subsequent bugs: 1. A future call to start_streaming() sees a non-NULL kthread_vid_cap and returns 0 (success) immediately, without actually starting the capture thread. 2. A call to stop_streaming() checks 'kthread_vid_cap == NULL' which is false for an error pointer, and proceeds to call kthread_stop()

• Actualiza a 6.12.111-1

media: zoran: Avoid freeing a registered video_device twice

In the Linux kernel, the following vulnerability has been resolved: media: zoran: Avoid freeing a registered video_device twice zoran_init_video_device() installs zoran_vdev_release() as the video_device release callback through zoran_template. After video_register_device() succeeds, video_unregister_device() drops the registered video_device reference and the V4L2 core eventually invokes that release callback, which kfree()s the video_device. zoran_exit_video_devices() called video_unregister_device() and then kfree(zr->video_dev), so device teardown could free the same video_device twice. Remove the direct kfree() and clear the cached p

• Actualiza a 6.12.111-1

media: chips-media: wave5: Add timeout while stop_streaming

In the Linux kernel, the following vulnerability has been resolved: media: chips-media: wave5: Add timeout while stop_streaming When stop_streaming is called, an infinite loop may occur in some cases. Add a bounded poll of the queue status: loop until the queues drain, sleeping briefly between polls, and bail out once VPU_DEC_STOP_TIMEOUT elapses.

• Actualiza a 6.12.113-1

media: chips-media: wave5: Resume device before setting EOS flag

In the Linux kernel, the following vulnerability has been resolved: media: chips-media: wave5: Resume device before setting EOS flag Setting the EOS flag talks to the firmware via send_firmware_command(), which accesses VPU registers. Both the STREAMOFF path (wave5_vpu_dec_job_abort()) and the V4L2_DEC_CMD_STOP path (wave5_vpu_dec_stop()) can run while the device is runtime suspended, so those register accesses hit powered-down hardware and the SoC raises an asynchronous SError, panicking the kernel: SError Interrupt on CPU3, code 0x00000000bf000000 -- SError send_firmware_command+0x2c/0x160 [wave5] wave5_vpu_dec_set_bitstream_flag

scsi: qla2xxx: Zero SFP DMA buffer in FRU/I2C bsg handlers

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Zero SFP DMA buffer in FRU/I2C bsg handlers The FRU and I2C bsg handlers stage their transfer in a DMA_POOL_SIZE (256-byte) bounce buffer obtained from dma_pool_alloc(), which does not zero the allocation. They initialize only a few leading bytes before handing the buffer to qla2x00_write_sfp(). qla2x00_write_sfp() can override the transfer length with a user-supplied value: if (len == 1) opt |= BIT_0; if (opt & BIT_0) len = *sfp; *sfp is the first byte of the (user-controlled) payload, so len can grow up to 255. The device then DMA-reads len bytes f

• Actualiza a 6.12.111-1

scsi: qla2xxx: Bound i2c->length in I2C bsg handlers

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Bound i2c->length in I2C bsg handlers struct qla_i2c_access carries a 16-bit length field alongside a fixed 64-byte buffer: struct qla_i2c_access { uint16_t device, offset, option, length; uint8_t buffer[0x40]; } __packed; qla2x00_write_i2c() and qla2x00_read_i2c() use the user-supplied i2c->length without any bounds check. i2c is overlaid on a 256-byte on-stack buffer and sfp is a 256-byte DMA-pool buffer, so a length up to 65535 overruns both: - write: memcpy(sfp, i2c->buffer, i2c->length) over-reads the stack and over-writes the sfp heap bu

• Actualiza a 6.12.111-1

scsi: qla2xxx: edif: Fix NULL pointer deref in RX SA delete check

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: edif: Fix NULL pointer deref in RX SA delete check qla_chk_edif_rx_sa_delete_pending() obtains the SCSI command via GET_CMD_SP(sp) and immediately dereferences cmd->sc_data_direction. That command pointer can be NULL: the firmware may post a status completion for a command that has already been returned or aborted. The caller qla2x00_status_entry() acknowledges this on the very same status path, re-fetching GET_CMD_SP(sp) and bailing out with the "Command already returned" message when it is NULL -- but that check runs only after qla_chk_edif_rx_sa_delete_pe

• Actualiza a 6.12.111-1

scsi: qla2xxx: Fix BSG job leak on validate flash image error path

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Fix BSG job leak on validate flash image error path qla28xx_validate_flash_image() returns QLA_SUCCESS (0) unconditionally, telling the FC BSG transport (fc_bsg_host_dispatch()) that the driver owns and will complete the request. But bsg_job_done() is guarded by "if (!rval)", so on the error path (rval == -EINVAL) neither the driver nor the transport completes the job. The request dangles until it times out, leaking block layer resources. Commit c2c68225b145 ("scsi: qla2xxx: Fix bsg_done() causing double free") added the "if (!rval)" guard to a batch of BSG

scsi: qla2xxx: Hold vport reference in qla24xx_report_id_acquisition()

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Hold vport reference in qla24xx_report_id_acquisition() In the format 1 path, the virtual port is located on ha->vp_list while holding vport_slock, but the lock is dropped before vp is used: qla_update_host_map() is called and VP_IDX_ACQUIRED/REGISTER_FC4_NEEDED/ REGISTER_FDMI_NEEDED are set on vp. No reference is taken across that window, so a concurrent qla24xx_deallocate_vp_id() can tear the vport down and free it, leading to a use-after-free. Take a vport reference (vref_count) under vport_slock when the matching vp is found, and drop it after the last u

• Actualiza a 6.12.111-1

scsi: qla2xxx: Initialize NVMe abort_work once at submission

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Initialize NVMe abort_work once at submission qla_nvme_fcp_abort() and qla_nvme_ls_abort() ran INIT_WORK() on priv->abort_work immediately before schedule_work(). INIT_WORK() reinitializes the work_struct, resetting its list head and clearing the pending bit. If an abort is issued more than once for the same command (for example, concurrent transport teardown and a timeout-driven abort), the second INIT_WORK() reinitializes a work item that is already queued, which can corrupt the workqueue list and lead to crashes or a looping worker. Initialize priv->abort

• Actualiza a 6.12.111-1

scsi: qla2xxx: Zero dport diagnostics buffer to avoid info leak

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Zero dport diagnostics buffer to avoid info leak qla2x00_do_dport_diagnostics() allocates the qla_dport_diag response buffer with kmalloc_obj() (non-zeroing) and, on success, copies the full sizeof(*dd) back to user space via sg_copy_from_buffer(). The inbound sg_copy_to_buffer() only fills as many bytes as the user request payload provides, and qla26xx_dport_diagnostics() zeroes only dd->buf. The options and unused[] fields are therefore copied out uninitialized, leaking kernel heap contents to user space. Allocate with kzalloc_obj(), matching qla2x00_do_dp

• Actualiza a 6.12.113-1

scsi: qla2xxx: Bound image count in qla2x00_update_fru_versions()

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Bound image count in qla2x00_update_fru_versions() qla2x00_update_fru_versions() copies the user-supplied BSG request into a fixed 256-byte stack buffer (bsg[DMA_POOL_SIZE]) and then iterates list->count times over the qla_image_version array embedded in that buffer, advancing the image pointer each iteration. count is taken directly from user input with no upper bound, while only (DMA_POOL_SIZE - sizeof(list->count)) / sizeof(struct qla_image_version) = 6 entries actually fit. A larger count walks the image pointer off the end of the stack buffer, reading ad

• Actualiza a 6.12.111-1

scsi: qla2xxx: Hold qpair lock when sending NVMe LS reject

In the Linux kernel, the following vulnerability has been resolved: scsi: qla2xxx: Hold qpair lock when sending NVMe LS reject qla_nvme_ls_reject_iocb() allocates from and advances the request ring through __qla2x00_alloc_iocbs() (which assumes the hardware_lock is held) and qla2x00_start_iocbs() (which advances the ring and rings the request-in doorbell), but takes no lock itself. Two of its callers invoke it without the producer lock held: - qla_nvme_xmt_ls_rsp(), the NVMe-FC .xmt_ls_rsp transport callback, on its error path, and - qla2xxx_process_purls_pkt(), run from the purex work/DPC context. Both use ha->base_qpair, whose qp_

• Actualiza a 6.12.111-1