power: supply: bq24257: fix use-after-free on remove
In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq24257: fix use-after-free on remove
The STAT-pin interrupt is devm-managed, so it stays armed until the devm
cleanup that runs after remove() returns. remove() cancels
bq->iilimit_setup_work while the threaded handler can still fire; that
handler reschedules the work and dereferences bq, so the work runs
against freed memory once devm frees bq.
Make the delayed work device-managed with devm_delayed_work_autocancel(),
registered before the interrupt request. The devm cleanup then releases
the interrupt first, so the handler can no longer reschedule the work
power: supply: bq256xx: drain usb_work before freeing the charger
In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq256xx: drain usb_work before freeing the charger
The USB-PHY notifier queues usb_work, whose handler calls
power_supply_changed(bq->charger). The reset devm action only unregisters
the notifier and was registered before the power supplies, so devm frees
bq->charger on unwind before the action runs; a usb_work still queued can
then dereference it.
Register the reset action after the power supplies, so it unregisters
the notifiers and drains usb_work before the supplies are released.
Initialize usb_work and obtain the PHY references before registering
the no
In the Linux kernel, the following vulnerability has been resolved:
power: supply: bq25890: Fix power_supply reference leak
bq25890_fw_probe() acquires a reference to a secondary charger using
power_supply_get_by_name(), but the reference is not released on later
probe failures or on driver detach.
In particular, failures after bq25890_fw_probe() returns successfully,
such as a failure in bq25890_hw_init(), also leak the reference.
Register a device-managed cleanup action immediately after acquiring
the secondary charger. This releases the reference on all subsequent
probe failures and on driver detach.
Found by code review.
power: supply: charger-manager: register regulators before exposing sysfs
In the Linux kernel, the following vulnerability has been resolved:
power: supply: charger-manager: register regulators before exposing sysfs
charger_manager_remove() and the err_reg_extcon probe error path free each
charger regulator with regulator_put() before tearing down the power_supply
sysfs entries (power_supply_unregister()). charger_manager_remove() also
calls try_charger_enable(cm, false) after the regulator_put() loop. A
concurrent write to a charger's externally_control sysfs attribute that
lands between regulator_put() and power_supply_unregister() can run
charger_externally_control_store() and call try_charger_enable(), which,
power: supply: cros_usbpd-charger: bound the EC-reported port count
In the Linux kernel, the following vulnerability has been resolved:
power: supply: cros_usbpd-charger: bound the EC-reported port count
cros_usbpd_charger_probe() reads two port counts from the EC and uses
one of them, num_charger_ports, as the loop bound when populating a
fixed-size array:
struct port_data *ports[EC_USB_PD_MAX_PORTS]; /* 8 entries */
...
for (i = 0; i < charger->num_charger_ports; i++)
charger->ports[charger->num_registered_psy++] = port;
Both num_usbpd_ports (from EC_CMD_USB_PD_PORTS) and num_charger_ports
(from EC_CMD_CHARGE_PORT_COUNT) are u8 values reported by the EC. The
only validation is a sanity check that c
power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS
In the Linux kernel, the following vulnerability has been resolved:
power: supply: cros_usbpd: Limit port counts to EC_USB_PD_MAX_PORTS
Currently the cros_usbpd-charger driver probe iterates based on raw
charger port count returned by the embedded controller. The only check
is against the number of USB PD ports which the embedded controller
also defines. A malicious embedded controller could return an inaccurate
port count (up to 255) resulting in an out of bounds write and
subsequent memory corruption.
Update helper functions in cros_usbpd-charger to limit port counts to
EC_USB_PD_MAX_PORTS.
power: supply: lp8727: fix use-after-free in lp8727_release_irq()
In the Linux kernel, the following vulnerability has been resolved:
power: supply: lp8727: fix use-after-free in lp8727_release_irq()
lp8727_isr_func(), the threaded IRQ handler, is the only caller that arms
pchg->work via schedule_delayed_work(). lp8727_release_irq() currently
cancels the work before freeing the IRQ, so an IRQ delivered in between
can re-arm the work through the threaded handler. After .remove returns
the devm layer frees pchg while lp8727_delayed_func() may still run and
dereference it.
Free the IRQ first so the threaded handler is quiesced and can no longer
queue work, then cancel the delayed work to drain the final g
power: supply: lp8788-charger: fix use-after-free on remove
In the Linux kernel, the following vulnerability has been resolved:
power: supply: lp8788-charger: fix use-after-free on remove
lp8788_charger_remove() flushes charger_work before unregistering the
IRQs. An IRQ thread can queue charger_work after flush_work() has
returned. The work can then run after devres frees pchg and dereference
it in lp8788_charger_event().
Unregister the IRQs first. free_irq() waits for any running threaded
handler, so no handler can queue more work afterwards. Then use
cancel_work_sync() to cancel pending work or wait for running work to
finish.
This issue was found by an in-house static analysis tool.
In the Linux kernel, the following vulnerability has been resolved:
power: supply: qcom_battmgr: fix use-after-free
qcom_battmgr_pdr_notify() queues enable_work when the PMIC GLINK service
comes up, and the worker recovers battmgr through container_of() to issue
firmware requests. The PMIC GLINK client stays on the client list until
its devres release action runs, so a PDR notification can keep queueing
the work, and a pending or running worker can access battmgr after devres
frees it.
Make enable_work device-managed with devm_work_autocancel(), registered
before the PMIC GLINK client is allocated. The devres cleanup then
releases the clie
power: supply: qcom_battmgr: terminate the strings from firmware
In the Linux kernel, the following vulnerability has been resolved:
power: supply: qcom_battmgr: terminate the strings from firmware
The qcom_battmgr_sc8280xp_strcpy() takes a Pascal-style string when the
firmware sends one. Otherwise it copies all BATTMGR_STRING_LEN bytes and
leaves the destination without a terminator.
Those destinations are model_number, serial_number and oem_info, each
BATTMGR_STRING_LEN and declared next to each other. They go out to user
space as val->strval, which power_supply_format_property() prints with
"%s", so a firmware string that fills the whole field makes that read run
into the following members.
Use strs
power: supply: rt9455: quiesce delayed work before teardown
In the Linux kernel, the following vulnerability has been resolved:
power: supply: rt9455: quiesce delayed work before teardown
The threaded IRQ handler can queue pwr_rdy_work,
max_charging_time_work and batt_presence_work. pwr_rdy_work and
batt_presence_work can also queue max_charging_time_work, while
batt_presence_work can requeue itself.
rt9455_remove() cancels max_charging_time_work before
batt_presence_work. The latter can therefore queue
max_charging_time_work after it has already been cancelled:
rt9455_remove() workqueue
cancel pwr_rdy_work
cancel max_charging_time_work
power: supply: twl4030_charger: cancel workers via devm
In the Linux kernel, the following vulnerability has been resolved:
power: supply: twl4030_charger: cancel workers via devm
bci is devm-allocated. Two workers (bci->work and bci->current_worker)
dereference it. twl4030_bci_remove() disables charging and masks
interrupts. It cancels neither worker. A worker pending at remove() can
run after devm frees bci.
The USB transceiver comes from devm_usb_get_phy_by_node(). devm
unregisters its notifier only after remove() returns. A cancel_work_sync()
in remove() can then race a notifier reschedule. devm_work_autocancel()
and devm_delayed_work_autocancel() avoid that. They cancel the workers
during
power: supply: ucs1002: fix use-after-free on remove
In the Linux kernel, the following vulnerability has been resolved:
power: supply: ucs1002: fix use-after-free on remove
ucs1002 has no remove callback, so unbind runs entirely through devm.
The alert IRQ handler queues the health_poll delayed work, and the work
reschedules itself while the chip reports a bad-health condition. devm
frees the alert IRQ, which only synchronizes the handler; it does not
cancel the delayed work, which can then run after devm frees the driver
data and dereference it.
Register health_poll with devm_delayed_work_autocancel() before the
alert IRQ is requested. devm then frees the IRQ before cancelling the
work,
In the Linux kernel, the following vulnerability has been resolved:
power: supply: max17040: propagate register read errors
max17040_get_vcell() and max17040_get_soc() ignore errors returned by
regmap_read(). When an I2C transfer fails, the uninitialized register
value is converted and reported to userspace as a valid voltage or state
of charge. The polling worker can also replace the cached state of charge
with the bogus value and emit a spurious change event.
Propagate read errors through the power supply get_property callback and
keep the last valid cached state of charge when polling fails.
power: supply: max17040: synchronize work cancellation on suspend
In the Linux kernel, the following vulnerability has been resolved:
power: supply: max17040: synchronize work cancellation on suspend
max17040_work() requeues itself after every poll. cancel_delayed_work()
only cancels a pending instance and does not wait for a callback that is
already running.
If system suspend races with the polling callback, the callback can
continue accessing the fuel gauge and requeue itself after the suspend
callback returns.
Use cancel_delayed_work_sync() to ensure polling is quiesced before
suspend completes.
s390/cpum_cf: Handle CPU hotplug via prepare/dead callbacks
In the Linux kernel, the following vulnerability has been resolved:
s390/cpum_cf: Handle CPU hotplug via prepare/dead callbacks
The command 'perf stat -e cycles -- <command>' crashes the kernel
when CPUs are hotplug added during that run.
Root cause is the allocation of struct cpu_cf_events at first
event initialization. The allocation is dynamic and the first
event that has task context creates such a structure for
each online CPU. This is not sufficient. CPUs may be offline
during event creation and can be set online during the
perf run time. For example commands
# echo 0 > /sys/devices/system/cpu/cpu1/online
# perf stat -e cycles -i
s390/dasd: Do not complete a failed ESE read as successful
In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: Do not complete a failed ESE read as successful
dasd_int_handler() completes an NRF read of an unallocated ESE track by
calling ese_read() and unconditionally marking the request
DASD_CQR_SUCCESS. dasd_eckd_ese_read() can return an error before it has
zeroed the destination buffer: a failed sense-data parse or a current
track outside the requested range both return early, leaving the
destination pages untouched. The request is still completed successfully,
so the block layer is handed stale / uninitialized memory instead of
zeros.
Check the ese_read() return val
s390/dasd: Guard sysfs discipline callbacks against unallocated private data
In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: Guard sysfs discipline callbacks against unallocated private data
Several sysfs show/store handlers call a discipline callback that
dereferences device->private, either directly or through the
DASD_DEFINE_ATTR() macro. During dasd_generic_set_online() the discipline
is assigned before check_device() allocates device->private, so an
unprivileged read of one of these world-readable attributes in that window
dereferences a NULL pointer and panics.
Guard the dereference inside each callback that actually touches
device->private.
s390/dasd: Propagate partial completion length across ERP recovery
In the Linux kernel, the following vulnerability has been resolved:
s390/dasd: Propagate partial completion length across ERP recovery
dasd_default_erp_postaction() copies the timing and device state from
the finished ERP request back to the original request but drops
proc_bytes. A request that was partially completed, an ESE read of a
not-yet-allocated track returns fewer bytes than requested, and then
recovered through the ERP chain loses its partial-completion length.
__dasd_cleanup_cqr() then sees proc_bytes == 0 and completes the whole
request instead of requeueing the remainder, silently returning zeroed
data for the part that was nev
PCI: plda: Fix use-after-free of event IRQs during teardown
In the Linux kernel, the following vulnerability has been resolved:
PCI: plda: Fix use-after-free of event IRQs during teardown
plda_pcie_irq_domain_deinit() removes pcie->event_domain via
irq_domain_remove(), but the per-event IRQs mapped from that domain
are requested with devm_request_irq() in plda_init_interrupts(). The
actual free_irq() for a devm-managed IRQ is deferred by devres until
after the calling probe()/remove() function returns.
This means irq_domain_remove() can free the domain's internal data
before the deferred free_irq() for IRQs still mapped into it has run.
When devres later processes that deferred cleanup, it can end