In the Linux kernel, the following vulnerability has been resolved:
bna: prevent IOC timer rearm during teardown
bna: prevent IOC timer rearm during teardown
bnad_pci_remove() and the probe disable_ioceth path call
timer_delete_sync() for ioc_timer, sem_timer and hb_timer, but not for
iocpf_timer. bnad_iocpf_timeout() then takes bnad->bna_lock after
free_netdev() has freed the struct bnad.
Deleting iocpf_timer last does not fix this. sem_timer and
iocpf_timer rearm each other: bnad_iocpf_sem_timeout() can arm
iocpf_timer, and bnad_iocpf_timeout() arms sem_timer from
bfa_ioc_hw_sem_get() when the semaphore is busy.
timer_delete_sync() on
ipv6: do not let ipv6_find_hdr() return an offset past the packet end
In the Linux kernel, the following vulnerability has been resolved:
ipv6: do not let ipv6_find_hdr() return an offset past the packet end
ipv6_find_hdr() walks the extension header chain, skipping each header by
the length that header itself declares. ipv6_optlen() returns up to 2048,
and the skip is never checked against skb->len, so the offset stored in
*offset can point past the end of the packet.
openvswitch installs that offset as the transport header, and
update_ipv6_checksum() then reads and writes the transport checksum field
out of bounds:
BUG: KASAN: slab-use-after-free in inet_proto_csum_replace16+0x445/0x470
Read of size
In the Linux kernel, the following vulnerability has been resolved:
llc: reserve device headroom for allocated frames
llc_alloc_frame() reserves link-layer headroom using the device type.
This is insufficient for stacked Ethernet devices such as VLAN devices,
where vlan_dev_hard_header() pushes a VLAN header before the lower
device's Ethernet header. An LLC response on such a device can
therefore underflow skb headroom in eth_header().
Use LL_RESERVED_SPACE() to account for the device's actual required
headroom while preserving the existing LLC device-type check.
mm/rmap: fix missing barrier between anon_vma init and vma->anon_vma publish
In the Linux kernel, the following vulnerability has been resolved:
mm/rmap: fix missing barrier between anon_vma init and vma->anon_vma publish
On arm64 server, we find that a task trying to grab the anon_vma lock
triggers hungtask.
INFO: task main:2354726 blocked for more than 120 seconds.
Tainted: G E 5.10.0-0021.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:main state:D stack: 0 pid:2354726 ppid:2350673 flags:0x00000a01
Call trace:
__switch_to+0x7c/0xbc
__schedule+0x3b4/0x8a0
schedule+0x50/0xe0
rwsem_down_write_slowpath+0x3cc/0x6cc
down_write+0x60/0x260
Media · CVSS 5.7EPSS 0,22%Sin corrección publicada
net: atl1: fix soft lockup on out-of-range cmb_tpd_next_to_clean read
In the Linux kernel, the following vulnerability has been resolved:
net: atl1: fix soft lockup on out-of-range cmb_tpd_next_to_clean read
Same issue as atl1c (see the first commit in this series, "net:
atl1c: fix soft lockup on out-of-range tpd_cons read"): the hardware
can report an out-of-range cmb_tpd_next_to_clean (seen as 0xffff)
while the PCIe link/MAC is resetting. An out-of-range value can
never be reached and the loop below would spin forever. Treat it as
"nothing new to clean" instead.
In the Linux kernel, the following vulnerability has been resolved:
net: ipconfig: bound DHCP option construction
ic_dhcp_init_options() appends the hostname (option 12), vendor-class
(option 60) and client-ID (option 61) options into the fixed 312-byte
bootp_pkt.exten[] buffer. Only the client-ID branch checked the
remaining space; the hostname and vendor-class writes were unbounded.
A 64-byte hostname together with the maximum 252-byte dhcpclass=
identifier needs 18 + (2 + 64) + (2 + 252) = 338 of the 312 available
bytes even before the terminating END marker, so the vendor-class memcpy
runs past the end of exten[]. With CONFIG_FORTIFY
net: atl1c: fix soft lockup on out-of-range tpd_cons read
In the Linux kernel, the following vulnerability has been resolved:
net: atl1c: fix soft lockup on out-of-range tpd_cons read
The hardware can report an out-of-range tpd_cons (seen as 0xffff)
while the PCIe link/MAC is resetting. An out-of-range value can
never be reached and the loop below would spin forever. To avoid
a soft lockup treat it as "nothing new to clean" instead.
Reproduced on two machines, same NIC (Qualcomm Atheros AR8151 v2.0,
4-port), triggered by rebooting a Mikrotik CCR2004 PCIe card that
the ports are directly linked to:
- Ubuntu 26.04.1 LTS, kernel 7.0.0-31-generic. The link-flap
precursor, before the lockup was cap
net: atl1e: fix soft lockup on out-of-range hw_next_to_clean read
In the Linux kernel, the following vulnerability has been resolved:
net: atl1e: fix soft lockup on out-of-range hw_next_to_clean read
Same issue as atl1c (see the first commit in this series, "net:
atl1c: fix soft lockup on out-of-range tpd_cons read"): the hardware
can report an out-of-range hw_next_to_clean (seen as 0xffff) while
the PCIe link/MAC is resetting. An out-of-range value can never be
reached and the loop below would spin forever. Treat it as "nothing
new to clean" instead.
net: ena: fix MMIO read buffer leak on probe failure
In the Linux kernel, the following vulnerability has been resolved:
net: ena: fix MMIO read buffer leak on probe failure
ena_device_init() initializes the MMIO read mechanism with
ena_com_mmio_reg_read_request_init(), which allocates a coherent DMA
buffer for MMIO read responses.
The normal removal path releases this buffer through
ena_com_mmio_reg_read_request_destroy(). However, if ena_probe() fails
after ena_device_init() succeeds, the error path destroys the admin
resources and eventually frees ena_dev without destroying the MMIO read
request, leaving the coherent DMA buffer allocated.
Call ena_com_mmio_reg_read_request_destroy() in t
netfilter: ip6t_rt: fix zero-address non-strict match out-of-bounds read
In the Linux kernel, the following vulnerability has been resolved:
netfilter: ip6t_rt: fix zero-address non-strict match out-of-bounds read
rt_mt6_check() permits rules to be configured with rtinfo->addrnr == 0
even when address matching (IP6T_RT_FST_MASK) is requested.
In the IP6T_RT_FST_NSTRICT path, rt_mt6() evaluates packet routing
addresses against rtinfo->addrs[i] and terminates backwards at the bottom
of the loop:
if (ipv6_addr_equal(ap, &rtinfo->addrs[i])) {
i++;
}
if (i == rtinfo->addrnr)
break;
When addrnr is 0, if the first packet address matches rtinfo->addrs[0],
i is incremented to 1. Because i i
Media · CVSS 5.3EPSS 0,21%Sin corrección publicada
nfc: llcp: drop truncated I/RR/RNR PDUs in nfc_llcp_recv_hdlc()
In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: drop truncated I/RR/RNR PDUs in nfc_llcp_recv_hdlc()
nfc_llcp_recv_hdlc() reads the sequence byte skb->data[2], via
nfc_llcp_ns()/nfc_llcp_nr(), before any length check. The receive path
only guarantees the two-byte LLCP header -- __nfc_llcp_recv() checks it
with pskb_may_pull() and nfc_llcp_recv_agf() admits two-byte inner PDUs
-- so a two-byte I, RR or RNR PDU reads one byte of uninitialised skb
tailroom. The byte becomes N(R)/N(S); a peer can already set those with
a well-formed PDU, so this is acting on uninitialised memory, not new
peer control.
Guard the r
Media · CVSS 5.1EPSS 0,22%Sin corrección publicada
nfc: port100: reject frames whose declared length exceeds the received data
In the Linux kernel, the following vulnerability has been resolved:
nfc: port100: reject frames whose declared length exceeds the received data
port100_recv_response() passes the URB transfer buffer to
port100_rx_frame_is_valid(), which checksums le16_to_cpu(frame->datalen)
bytes of frame->data. datalen is a 16-bit field supplied by the device
and is never checked against the number of bytes actually received
(urb->actual_length), so a device reporting a datalen larger than the
received frame makes port100_data_checksum() read out of bounds past the
transfer buffer.
Reject a response whose declared frame size does not fit the received
leng
scsi: libiscsi_tcp: Check the data direction of a Data-In PDU
In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Check the data direction of a Data-In PDU
The Data-In branch of iscsi_tcp_hdr_dissect() resolves the ITT to a task
and copies the PDU's data segment into that command's scatterlist without
asking whether the command was reading. iscsi_tcp_r2t_rsp() in the same
file does ask, and rejects an R2T for a command that is not DMA_TO_DEVICE.
A target that answers a WRITE command's ITT with a Data-In therefore has
the initiator write target-supplied bytes into the pages that write was
about to send. Those are the caller's own pinned pages for an O_DIRECT
write,
Media · CVSS 4.1EPSS 0,22%Sin corrección publicada
Bluetooth: hci_sock: validate event length before filtering
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: validate event length before filtering
is_filtered_packet() reads the event code from skb->data[0] without first
checking that the skb is nonempty. When an opcode filter is configured,
it also reads the command opcode at offsets 3 or 4 without checking that
a Command Complete or Command Status event is long enough.
hci_send_to_sock() invokes the filter before hci_event_packet() validates
the event header. A malformed event supplied by a controller or a vhci
device can therefore cause an out-of-bounds read.
Keep the unmasked event code for the opcode c
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: reject out-of-range OCF values
The raw HCI socket security filter has 128 OCF bits per supported OGF,
but masks the 10-bit OCF with 127 before looking up the command. An
unprivileged socket can therefore submit a reserved OCF that aliases an
allowlisted command modulo 128.
A conforming controller should reject reserved opcodes. Nevertheless,
the security decision must apply to the opcode that will actually be
sent, especially since controller-specific behavior is outside the host
stack's control.
Reject OCF values that cannot be represented by the sec
Bluetooth: L2CAP: validate frame length before control and FCS access
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: validate frame length before control and FCS access
l2cap_data_rcv() unpacks either a two-byte or four-byte control field
without first ensuring that it is present. A short ERTM or streaming-mode
frame can therefore cause an out-of-bounds read.
There is a second short-frame case when CRC16 is enabled. After the
control field is pulled, l2cap_check_fcs() subtracts two from skb->len
without checking it. If fewer than two bytes remain, the subtraction
wraps; skb_trim() leaves the buffer unchanged and the subsequent FCS
load reads past the logical end of the
Media · CVSS 5.7EPSS 0,18%Sin corrección publicada
Bluetooth: RFCOMM: fix NULL dereference of dlc->session in RFCOMM_CONNINFO
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: fix NULL dereference of dlc->session in RFCOMM_CONNINFO
The RFCOMM_CONNINFO getsockopt handler accepts a socket that is not
connected as long as deferred setup is enabled:
if (sk->sk_state != BT_CONNECTED &&
!rfcomm_pi(sk)->dlc->defer_setup) {
err = -ENOTCONN;
break;
}
l2cap_sk = rfcomm_pi(sk)->dlc->session->sock->sk;
dlc->defer_setup is set in rfcomm_sock_init() when rfcomm_connect_ind()
creates a child socket for an incoming connection on a listening socket
that has BT_DEFER_SETUP enabled. It is never cleared afterwards. The
session, howeve
In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix create context out-of-bounds reads
smb2_parse_contexts() validates the complete create-context area but
does not limit each record to its Next field before dispatching it. A
malformed chain can therefore expose bytes beyond the current context to
a handler. The QFid handler also used a full response-structure cast
although it only reads DiskFileId.
The SMB2/SMB3 lease parsers made the same layout assumption: they read
LeaseState and LeaseFlags at canonical offsets rather than at
DataOffset. A valid non-canonical DataOffset could therefore yield
unrelate
smb: client: use finish_no_open() for non-regular inodes
In the Linux kernel, the following vulnerability has been resolved:
smb: client: use finish_no_open() for non-regular inodes
An O_CREAT open can find an existing symlink or another non-regular
inode. cifs_atomic_open() calls finish_open() on it and attaches a
cifsFileInfo. Symlink inodes have no CIFS release operation, so the
dentry reference held by cifsFileInfo is leaked. FMODE_OPENED also
prevents the VFS from following the symlink.
Track whether cifs_do_create() returned an open server handle. For
non-regular inodes, close the handle if present, remove the pending
open, and call finish_no_open() so the VFS can continue the lookup.
Do n
smb/server: cancel async requests when closing connection
In the Linux kernel, the following vulnerability has been resolved:
smb/server: cancel async requests when closing connection
An async request may still be waiting when a connection is closed.
This can stop the connection from closing.
Cancel active async requests before waiting for them to finish.