fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX.
In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter deregistration race
Adapters can be looked up by their id using i2c_get_adapter() which
takes a reference to the embedded struct device.
Remove the adapter from the IDR before tearing it down during
deregistration (and on registration failure) to make sure its resources
are not accessed after having been freed (e.g. the device name).
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
rmi_f3a_initialize() takes the GPIO count from the device query register
(f3a->gpio_count = buf & RMI_F3A_GPIO_COUNT, range 0..127).
rmi_f3a_map_gpios() then allocates gpio_key_map with
min(gpio_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f3a_attention() iterates the full gpio_count and dereferences
gpio_key_map[i], and input->keycodemax is set to the full gpio_count
while input->keycode points at the 6-entry allocation.
A device that reports gpio_count > 6 therefore causes an out-of-bounds
read
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
rmi_f30_map_gpios() allocates gpioled_key_map with
min(gpioled_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f30_attention() iterates the full f30->gpioled_count (device query
register, range 0..31) and dereferences gpioled_key_map[i], and
input->keycodemax is set to the full gpioled_count while input->keycode
points at the 6-entry allocation.
A device that reports gpioled_count > 6 with GPIO support enabled
therefore causes an out-of-bounds read on the attention interrupt and
out-of-bounds rea
Input: elan_i2c - prevent division by zero and arithmetic underflow
In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - prevent division by zero and arithmetic underflow
The Elan I2C touchpad driver queries the device for its physical
dimensions and trace counts to calculate the device resolution and width.
However, if the device firmware or device tree provides invalid zero
values for x_traces or y_traces, it results in a fatal division-by-zero
exception leading to a kernel panic during device probe.
Add checks to ensure these parameters are non-zero before performing
the division. If invalid trace values are detected, fall back to a safe
default of 1.
Additionally, prev
Input: goodix - clamp the device-reported contact count
In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a mal
Input: iforce - bound the device-reported force-feedback effect index
In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds
Input: mms114 - fix touch indexing for MMS134S and MMS136
In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by expli
Input: touchwin - reset the packet index on every complete packet
In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes diffe
Input: mms114 - reject an oversized device packet size
In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - reject an oversized device packet size
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device registe
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
When the server answers an RTRS READ, rdma_write_sg() builds the source
scatter/gather entry for the IB_WR_RDMA_WRITE that returns data to the
peer. Its length is taken directly from the wire descriptor:
plist->length = le32_to_cpu(id->rd_msg->desc[0].len);
rd_msg points into the chunk buffer that the remote peer filled via
RDMA-WRITE-WITH-IMM (rtrs_srv_rdma_done() -> process_io_req() ->
process_read()), so desc[0].len is attacker-controlled and, before this
change, was only rejected when zero. The so
RDMA/siw: bound Read Response placement to the RREAD length
In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: bound Read Response placement to the RREAD length
In drivers/infiniband/sw/siw/siw_qp_rx.c, siw_proc_rresp() places each
inbound Read Response DDP segment at sge->laddr + wqe->processed and then
accumulates wqe->processed, but it never checks the running total against
the sink buffer length on continuation segments. siw_check_sge() resolves
and validates the sink memory only on the first fragment (the if (!*mem)
branch), and siw_rresp_check_ntoh() compares the cumulative length against
wqe->bytes only on the final segment (the !frx->more_ddp_segs guard).
A connec
fuse: re-lock request before returning from fuse_ref_folio()
In the Linux kernel, the following vulnerability has been resolved:
fuse: re-lock request before returning from fuse_ref_folio()
fuse_ref_folio() unlocks the request but does not re-lock it before
returning. fuse_chan_abort() can end the request and the async end
callback (eg fuse_writepage_free()) can free the args while the
subsequent copy chain logic after fuse_ref_folio() accesses them,
leading to use-after-free issues.
Fix this by locking the request in fuse_ref_folio() before returning.
smb: client: reject overlapping data areas in SMB2 responses
In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions.
fpga: region: fix use-after-free in child_regions_with_firmware()
In the Linux kernel, the following vulnerability has been resolved:
fpga: region: fix use-after-free in child_regions_with_firmware()
Move of_node_put(child_region) after the error print to avoid accessing
freed memory when pr_err() references child_region.
[ Yilun: Fix the Fixes tag ]
power: reset: linkstation-poweroff: fix use-after-free in the linkstation_poweroff_init()
In the Linux kernel, the following vulnerability has been resolved:
power: reset: linkstation-poweroff: fix use-after-free in the linkstation_poweroff_init()
Move of_node_put(dn) after the of_match_node() call, which still needs
the node pointer. The node reference is correctly released after use.
ASoC: codecs: simple-mux: Fix enum control bounds check
In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: simple-mux: Fix enum control bounds check
simple_mux_control_put() rejects values greater than e->items, but
enum control values are zero based. For the two-entry mux used by this
driver, valid values are 0 and 1, so value 2 must be rejected as well.
Accepting e->items can store an invalid mux state, pass it to the GPIO
setter, and pass it on to the DAPM mux update path where it is used as
an index into the enum text array.
Use the same >= e->items check used by the ASoC enum helpers.
usb: gadget: net2280: Fix double free in probe error path
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: net2280: Fix double free in probe error path
usb_initialize_gadget() installs gadget_release() as the release
callback for the embedded gadget device. The struct net2280 instance is
therefore released through gadget_release() when the gadget device's last
reference is dropped.
The probe error path calls net2280_remove(), which tears down the
partially initialized device and drops the gadget reference with
usb_put_gadget(). Calling kfree(dev) afterwards can free the same object
again.
Drop the explicit kfree() and let the gadget device release callback
handl
Media · CVSS 5.5EPSS 0,11%Sin corrección publicada
gpio: rockchip: teardown bugs and resource leaks
In the Linux kernel, the following vulnerability has been resolved:
gpio: rockchip: teardown bugs and resource leaks
Address several teardown issues and resource leaks in the driver's remove
path and error handling:
1. Debounce clock reference leak: The debounce clock (bank->db_clk) is
obtained using of_clk_get() which increments the clock's reference
count, but clk_put() is never called. Register a devm action to
cleanly release it on unbind. Note that of_clk_get(..., 1) remains
necessary over devm_clk_get() because the DT binding does not define
clock-names, precluding name-based lookup.
2. Unregistered chained IRQ handle
Input: elan_i2c - validate firmware size before use
In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads.