net: thunderbolt: Fix frags[] overflow by bounding frame_count
In the Linux kernel, the following vulnerability has been resolved:
net: thunderbolt: Fix frags[] overflow by bounding frame_count
tbnet_poll() assembles a multi-frame ThunderboltIP packet into one skb. The
first frame goes into the skb linear area and every further frame is added as
a page fragment.
skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags,
page, hdr_size, frame_size,
TBNET_RX_PAGE_SIZE - hdr_size);
A packet of frame_count frames therefore ends up with frame_count - 1
fragments. tbnet_check_frame() only bounds the peer supplied frame_count to
TBNET_RING_SIZE / 4 (64), which is far above MAX_SKB_FRAGS (17 by default). A
peer
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
In the Linux kernel, the following vulnerability has been resolved:
fpga: microchip-spi: fix zero header_size OOB read in mpf_ops_parse_header()
mpf_ops_parse_header() reads header_size from the bitstream at
MPF_HEADER_SIZE_OFFSET (24). When header_size is zero, the expression
*(buf + header_size - 1) reads one byte before the buffer start.
Since initial_header_size is set to 71 in mpf_ops, the fpga-mgr core
guarantees the buffer is large enough to reach MPF_HEADER_SIZE_OFFSET.
The only real gap is the zero header_size case, which cannot be
resolved by providing a larger buffer, so return -EINVAL.
mtd: spi-nor: swp: Improve locking user experience
In the Linux kernel, the following vulnerability has been resolved:
mtd: spi-nor: swp: Improve locking user experience
In the case of the first block being locked (or the few first blocks),
if the user want to fully unlock the device it has two possibilities:
- either it asks to unlock the entire device, and this works;
- or it asks to unlock just the block(s) that are currently locked,
which fails.
It fails because the conditions "can_be_top" and "can_be_bottom" are
true. Indeed, in this case, we unlock everything, so the TB bit does not
matter. However in the current implementation, use_top would be true (as
this is the favourite optio
irqchip/crossbar: Use correct index in crossbar_domain_free()
In the Linux kernel, the following vulnerability has been resolved:
irqchip/crossbar: Use correct index in crossbar_domain_free()
crossbar_domain_free() resets the domain data and then uses the nulled
out irq_data->hwirq member as index to reset the irq_map[] entry and to
write the relevant crossbar register with a safe entry. That means it
never frees the correct index and keeps the crossbar register connection
to the source interrupt active.
If it would not reset the domain data, then this would be even worse as
irq_data->hwirq holds the source interrupt number, but both the map and
register index need the corresponding GIC SPI number an
tpm: tpm_tis_spi: Use wait_woken() in wait_for_tmp_stat()
In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_tis_spi: Use wait_woken() in wait_for_tmp_stat()
wait_event_interruptible_timeout() evaluates its condition after setting
the current task state to TASK_INTERRUPTIBLE.
With CONFIG_DEBUG_ATOMIC_SLEEP this triggers a warning when the IRQ wait
path is used:
tpm_tis_status()
tpm_tis_spi_read_bytes()
tpm_tis_spi_transfer_full()
spi_bus_lock()
mutex_lock()
Address this with the following measures:
1. Call wait_tpm_stat_cond() only while tasking is running.
2. Use wait_woken() to wait for changes.
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: tegra: Fix burst size calculation
Currently, the Tegra GPC DMA hardware requires the transfer length to
be a multiple of the max burst size configured for the channel. When a
client requests a transfer where the length is not evenly divisible by
the configured max burst size, the DMA hangs with partial burst at
the end.
Fix this by reducing the burst size to the largest power-of-2 value
that evenly divides the transfer length. For example, a 40-byte
transfer with a 16-byte max burst will now use an 8-byte burst
(40 / 8 = 5 complete bursts) instead of causing a h
dmaengine: dw-edma: Add spinlock to protect DONE_INT_MASK and ABORT_INT_MASK
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: dw-edma: Add spinlock to protect DONE_INT_MASK and ABORT_INT_MASK
The DONE_INT_MASK and ABORT_INT_MASK registers are shared by all DMA
channels, and modifying them requires a read-modify-write sequence.
Because this operation is not atomic, concurrent calls to
dw_edma_v0_core_start() can introduce race conditions if two channels
update these registers simultaneously.
Add a spinlock to serialize access to these registers and prevent race
conditions.
[den: update dw_edma.lock comment]
dmaengine: dw-edma-pcie: Reject devices without driver data
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: dw-edma-pcie: Reject devices without driver data
dw_edma_pcie_probe() treats the PCI device ID driver_data as the
template for the controller layout and copies it unconditionally. A
device bound dynamically via sysfs can match the driver without that
data, which leads to a NULL pointer dereference.
Reject such matches before enabling the device.
dmaengine: sh: rz-dmac: Move interrupt request after everything is set up
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: sh: rz-dmac: Move interrupt request after everything is set up
Once the interrupt is requested, the interrupt handler may run immediately.
Since the IRQ handler can access channel->ch_base, which is initialized
only after requesting the IRQ, this may lead to invalid memory access.
Likewise, the IRQ thread may access uninitialized data (the ld_free,
ld_queue, and ld_active lists), which may also lead to issues.
Request the interrupts only after everything is set up. To keep the error
path simpler, use dmam_alloc_coherent() instead of dma_alloc_coherent().
platform/x86: dell-laptop: fix missing cleanups in init error path
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-laptop: fix missing cleanups in init error path
dell_init() initializes several resources after dell_setup_rfkill(),
including the optional touchpad LED, keyboard backlight LED, battery
hook, debugfs directory and dell-laptop notifier.
If a later LED or backlight registration fails, the error path only
tears down the battery hook and rfkill resources. This leaves the
notifier, debugfs directory, keyboard backlight LED and optional
touchpad LED registered after dell_init() returns an error.
Add the missing cleanup calls before tearing down rfkill.
i2c: imx: fix locked bus on SMBus block-read of 0 (atomic)
In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix locked bus on SMBus block-read of 0 (atomic)
SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the atomic
(polling) path rejects it as -EPROTO. Worse, it returns without a
NACK+STOP: the next receive cycle has already started, so the target
keeps holding SDA and the bus stays stuck until a power cycle for
this i2c controller.
Reading I2DR to obtain the count likewise arms the next byte on the
count > I2C_SMBUS_BLOCK_MAX path, which also returned -EPROTO directly
and left the bus held.
Handle both: NACK the in-flight dummy byte (TXAK) and extend msgs->
i2c: mlxbf: Fix use-after-free in mlxbf_i2c_init_resource()
In the Linux kernel, the following vulnerability has been resolved:
i2c: mlxbf: Fix use-after-free in mlxbf_i2c_init_resource()
If devm_platform_get_and_ioremap_resource() returns an error,
mlxbf_i2c_init_resource() frees tmp_res before reading tmp_res->io to
get the error code. This results in a use-after-free.
Save the error code before freeing tmp_res.
In the Linux kernel, the following vulnerability has been resolved:
xen/gntdev: fix error handling in ioctl
When gntdev_ioctl_map_grant_ref() fails to copy the operation result
back to userspace after successfully adding the mapping to the list,
the error path returns -EFAULT without releasing the reference
acquired by gntdev_alloc_map(). The mapping remains in priv->maps
with a refcount of 1, causing a memory leak and a dangling list
entry.
Additionally, gntdev_add_map() may modify map->index to avoid overlap
with existing mappings. Therefore, the index returned to userspace
must be obtained after gntdev_add_map() completes.
Fix this by
xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink
In the Linux kernel, the following vulnerability has been resolved:
xfrm: xfrm_interface: require CAP_NET_ADMIN in the device netns for changelink
xfrmi_changelink() operates on at most two netns, dev_net(dev) and the
interface link netns xi->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in xi->net can rewrite an interface that
lives in xi->net.
Gate xfrmi_changelink() on rtnl_dev_link_net_capable() at its top,
before any attribute is parsed.
In the Linux kernel, the following vulnerability has been resolved:
tpm: Make the TPM character devices non-seekable
The TPM character devices expose a sequential command/response
interface, but their open handlers leave FMODE_PREAD and FMODE_PWRITE
enabled.
After a command leaves a response pending, pread(fd, buf, 16, 0x1400)
passes 0x1400 as *off to tpm_common_read(). The transfer length is
bounded by response_length, but the offset is used unchecked when
forming data_buffer + *off. A sufficiently large offset therefore causes
an out-of-bounds heap read through copy_to_user() and, if the copy
succeeds, an out-of-bounds zero-write through
spi: uniphier: Fix completion initialization order before devm_request_irq()
In the Linux kernel, the following vulnerability has been resolved:
spi: uniphier: Fix completion initialization order before devm_request_irq()
The driver calls devm_request_irq() before initializing the completion
used by the interrupt handler. Because the interrupt may occur immediately
after devm_request_irq(), the handler may execute before init_completion().
This may result in calling complete() on an uninitialized completion,
causing undefined behavior. This has been observed with KASAN.
Fix this by initializing the completion before registering the IRQ.
NFS: Charge unstable writes by request size, not folio size
In the Linux kernel, the following vulnerability has been resolved:
NFS: Charge unstable writes by request size, not folio size
nfs_folio_mark_unstable() and nfs_folio_clear_commit() charge and
uncharge NR_WRITEBACK/WB_WRITEBACK by folio_nr_pages(folio) once per
*request* added to or removed from a commit list. This is correct only
when a folio has a single associated request. When pg_test splits a
folio into N sub-folio requests (e.g. pNFS flexfiles striping with a
stripe unit smaller than the folio size, or plain wsize-limited
splitting), each of the N requests independently charges the whole
folio's page count, inflating the accounting b
In the Linux kernel, the following vulnerability has been resolved:
nvmet-auth: reject short AUTH_RECEIVE buffers
nvmet_execute_auth_receive() trusts the AUTH_RECEIVE allocation length
after checking only that it is nonzero and matches the transfer length.
In the SUCCESS1 and FAILURE1/default states, that lets a remote NVMe-oF
initiator reach the fixed-size DH-HMAC-CHAP response builders with a
kmalloc() buffer shorter than the response, so nvmet_auth_success1() and
nvmet_auth_failure1() write past the allocation; both only WARN_ON the
short length and then format the message anyway.
Impact: A remote NVMe-oF initiator with access to an aut
nvmet-rdma: handle inline data with a nonzero offset
In the Linux kernel, the following vulnerability has been resolved:
nvmet-rdma: handle inline data with a nonzero offset
nvmet_rdma_use_inline_sg() maps the host-controlled inline data offset
into the per-command inline scatterlist. The bounds check admits any
offset with off + len <= inline_data_size, but the mapping still assumes
the data begins in the first inline page:
sg->offset = off;
sg->length = min_t(int, len, PAGE_SIZE - off);
When a port is configured with inline_data_size > PAGE_SIZE (settable up
to max(SZ_16K, PAGE_SIZE)), an offset in (PAGE_SIZE, inline_data_size]
makes "PAGE_SIZE - off" underflow, so sg->length is set to
netdev-genl: report NAPI thread PID in the caller's pid namespace
In the Linux kernel, the following vulnerability has been resolved:
netdev-genl: report NAPI thread PID in the caller's pid namespace
netdev_nl_napi_fill_one() reports the NAPI kthread PID in NETDEV_A_NAPI_PID
using task_pid_nr(), which returns the PID in the initial pid namespace.
NETDEV_CMD_NAPI_GET does not have GENL_ADMIN_PERM and the netdev genl family
is netnsok, so a caller in a child pid namespace can issue it. That caller
then sees the kthread's global PID, even though the kthread is not visible
in its pid namespace, where the value should be 0.
Translate the PID through the caller's pid namespace, the same way commit
3799c257098