wifi: mt76: mt7915: fix double hif2 init on the non-WED path
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix double hif2 init on the non-WED path
mt7915_pci_init_hif2() was called unconditionally and again inside the
WED-inactive branch. The helper increments the global hif_idx, writes the
PCIe RECOG_ID register and takes a get_device() reference via
mt7915_pci_get_hif2(), while removal only drops one reference. On non-WED
dual-hif hardware this double-incremented hif_idx, wrote RECOG_ID twice and
leaked a device reference. Only the call inside the WED-inactive branch is
correct; drop the unconditional one. hif2 is already initialised to NULL.
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: fix ext PHY use-after-free on register error path
After mt7915_register_ext_phy() succeeded, a failure of the main PHY
mt7915_init_debugfs() or mt7915_coredump_register() unwound through
free_phy2, which called ieee80211_free_hw() on the ext PHY hw while it
was still registered with mac80211, since mt76_unregister_device() only
unregisters the main hw. Unregister the ext PHY (thermal + phy + hw)
first and skip the redundant free.
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: release hif2 reference on probe IRQ failure
The hif2 reference obtained by mt7915_pci_init_hif2() is only released on
error paths that key off dev->hif2, which is not assigned until after the
IRQ setup. If pci_alloc_irq_vectors() or the primary devm_request_irq()
fails, the reference leaks. Drop it explicitly on those paths via
mt7915_put_hif2().
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: do not attach hif2 WED when the main WED attach failed
If the WED attach for the primary PCIe function fails, the probe path
still attached wed_hif2 for the secondary function, leaving the device
in an inconsistent half-WED configuration that crashes later. The hif2
call also re-enabled hwrro_mode, which the failed primary attach had
just turned off.
Skip the hif2 WED setup when the primary WED device is not active.
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
In the Linux kernel, the following vulnerability has been resolved:
wifi: ath10k: snoc: use memcpy_fromio() for MSA ramdump
On WCN3990/SNOC the MSA region is mapped with devm_memremap(MEMREMAP_WT).
On arm64 such a mapping is not Normal-cacheable, so unaligned accesses to
it are not permitted. ath10k_msa_dump_memory() copies the region with a
plain memcpy(), whose optimized __pi_memcpy_generic implementation issues
wide/unaligned loads. This triggers an alignment fault (FSC=0x21) Oops in
ath10k_snoc_fw_crashed_dump() while collecting the devcoredump:
Unable to handle kernel paging request ... FSC=0x21: alignment fault
pc : __pi_memcpy_g
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core se
wifi: nl80211: clean up color-change beacon data on errors
In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data.
wifi: brcmfmac: fix P2P action frame handling without device vif
In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search.
wifi: cfg80211: stop PMSR before P2P and NAN teardown
In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: stop PMSR before P2P and NAN teardown
PMSR request teardown must abort active measurements while the
wireless_dev is still present in the driver. cfg80211_leave_locked() and
cfg80211_stop_pd() already do this before invoking the driver's stop
callback, but cfg80211_stop_p2p_device() and cfg80211_stop_nan() do not.
Those helpers are also called directly by nl80211, rfkill shutdown, and
wireless_dev unregister paths. If one of these paths stops a P2P device
or NAN interface with a pending request, it removes the mac80211
subinterface from the driver first. Su
In the Linux kernel, the following vulnerability has been resolved:
firmware: coreboot: Validate table bounds
The existing coreboot_table_populate() bounds checks limit individual
entries to the mapped length. However, coreboot_table_probe() replaces
the platform resource length with header and table sizes supplied by
firmware before mapping the full table.
A malformed table can overflow the 32-bit size addition or advertise an
extent beyond the resource, causing the driver to map and parse memory
outside the resource. A resource shorter than the fixed header is also
mapped as though it contained a complete header.
Reject resources shor
serial: core: do fallible allocations before the console can be registered
In the Linux kernel, the following vulnerability has been resolved:
serial: core: do fallible allocations before the console can be registered
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before li
serial: core: clear freed pointers on uart_register_driver() failure
In the Linux kernel, the following vulnerability has been resolved:
serial: core: clear freed pointers on uart_register_driver() failure
uart_register_driver() leaves drv->state pointing to freed memory when
tty_alloc_driver() fails. If tty_register_driver() fails, drv->tty_driver
also retains a pointer after its reference is dropped.
Drivers that use drv->state as an "already registered" flag can then skip
registration on the next probe and pass the freed state to
uart_add_one_port().
This issue was found with failslab on QEMU's raspi1ap board by
failing registration and binding the PL011 port again.
Clear both pointers on their failure
In the Linux kernel, the following vulnerability has been resolved:
tty: skip cdev_del() when no cdev is registered
TTY device registration can fail before a cdev is allocated.
Serial core keeps the port so setserial can still use it, and later
removal passes the NULL cdev slot to cdev_del(), causing a NULL-pointer
dereference.
Only delete the cdev when the slot is not NULL.
In the Linux kernel, the following vulnerability has been resolved:
tty: clear cdev pointer after cdev_add() failure
tty_cdev_add() drops the cdev reference when cdev_add() fails, but
leaves driver->cdevs[index] pointing to freed memory.
tty_unregister_device() later passes that stale pointer to cdev_del(),
causing a use-after-free.
Clear the slot after dropping the reference.
dm-integrity: replace forgeable discard filler with a keyed sector marker
In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: replace forgeable discard filler with a keyed sector marker
The discard-block check in dm_integrity_rw_tag() treats a stored tag
of all 0xf6 bytes (DISCARD_FILLER) as proof a block was discarded and
skips HMAC verification. allow_discards is only accepted in
dm-integrity's standalone mode. An attacker with raw write access to
the backing device, but without the integrity key, can stamp any block
with an all-0xf6 tag and have it served as authentic.
Add a new "allow_discards_keyed" target argument that marks discarded
blocks with a keyed checksum of (salt || s
HID: logitech-hidpp: Fix FF device cleanup on init failure
In the Linux kernel, the following vulnerability has been resolved:
HID: logitech-hidpp: Fix FF device cleanup on init failure
hidpp_ff_init() creates the input force-feedback device with
input_ff_create(), then allocates the HID++ FF private data,
effect ID array, and workqueue.
If any of those allocations fail after input_ff_create() succeeds,
the function returns an error without destroying the FF device.
Add an unwind path that frees the private allocations made by
hidpp_ff_init() and calls input_ff_destroy() for failures after
input_ff_create() succeeds.
HID: synchronize input before cleaning up a failed probe
In the Linux kernel, the following vulnerability has been resolved:
HID: synchronize input before cleaning up a failed probe
hid_device_io_start() allows reports to run concurrently with probe. If
the probe subsequently fails, __hid_device_probe() releases driver
resources and clears hdev->driver without first excluding those report
callbacks.
For example, a report may enter hidraw_report_event() while the failure
path frees the associated hidraw object, leading to a use-after-free when
the report takes the object's list lock.
Stop input before performing failed-probe cleanup. This reacquires
driver_input_lock and waits for any report cal
In the Linux kernel, the following vulnerability has been resolved:
HID: steam: Reject short reads
Steam Controller FEATURE reports encode the size of the message in the
message itself. Previously we were trusting that the size reported matched
the size we actually read, leading to a potential issue with short reads.
Instead, we should actually verify the length of the read.
phonet: pep: do not write beyond optlen in getsockopt
In the Linux kernel, the following vulnerability has been resolved:
phonet: pep: do not write beyond optlen in getsockopt
pep_getsockopt() clamps the reported length to the caller's buffer with
min_t(), but then stores the value with put_user(val, (int __user *)
optval), which always writes sizeof(int) bytes. A getsockopt() call with
an optlen smaller than sizeof(int) thus reports the clamped length yet
writes a full int, one to three bytes past the user buffer.
Write the value with copy_to_user() bounded by len, so at most optlen
bytes are copied, matching the length reported back to userspace.
blk-cgroup: fix race between policy activation and blkg destruction
In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: fix race between policy activation and blkg destruction
When switching an IO scheduler on a block device, blkcg_activate_policy()
allocates blkg_policy_data (pd) for all blkgs attached to the queue.
However, blkcg_activate_policy() may race with concurrent blkcg deletion,
leading to use-after-free and memory leak issues.
The use-after-free occurs in the following race:
T1 (blkcg_activate_policy):
- Successfully allocates pd for blkg1 (loop0->queue, blkcgA)
- Fails to allocate pd for blkg2 (loop0->queue, blkcgB)
- Enters the enomem rollback path to releas