net: bridge: avoid recursive multicast port cleanup
In the Linux kernel, the following vulnerability has been resolved:
net: bridge: avoid recursive multicast port cleanup
br_multicast_sg_del_exclude_ports() removes automatically added STAR_EXCL
port groups by calling br_multicast_del_pg(). For S,G entries, that
deletion calls back into br_multicast_sg_del_exclude_ports(), so a large
number of STAR_EXCL ports consumes one kernel stack frame per port and can
hit the stack guard page.
Keep the complete port-group deletion path for cleanup, but suppress the
S,G exclude-port cleanup while that helper is already walking the same
entry. Normal deletion callers retain the existing behavior.
net: skbuff: don't leave stale bytes in skb_copy_and_csum_bits()
In the Linux kernel, the following vulnerability has been resolved:
net: skbuff: don't leave stale bytes in skb_copy_and_csum_bits()
When skb_copy_and_csum_bits() reaches unreadable frags it returns 0
after copying only the linear part, and the rest of the caller's buffer
is left as it was. The callers copy into a buffer that is about to go
out on the wire: an ICMP error quoting the offending packet, or a
driver's TX bounce buffer in skb_copy_and_csum_dev(). Neither buffer
is zeroed beforehand, so whatever was in memory there gets sent.
Zero the part of the buffer we didn't fill. The checksum usually
won't match the data any more, so th
In the Linux kernel, the following vulnerability has been resolved:
net: sparx5: free the matchall entry on destroy
sparx5_tc_matchall_replace() allocates a struct sparx5_mall_entry for
every offloaded matchall filter and adds it to sparx5->mall_entries.
sparx5_tc_matchall_destroy() removes the entry from the list, but never
frees it, so the entry of every deleted mirror and goto matchall filter
is leaked.
Free the entry after unlinking it.
The leak was discovered by an AI code review agent, and reproduced with
kmemleak on a lan969x EV board (EV23X71A) by repeatedly adding and
deleting matchall mirror and goto filters. With the fix, kmeml
net: xilinx: axienet: Free outstanding DMA buffers on dmaengine stop
In the Linux kernel, the following vulnerability has been resolved:
net: xilinx: axienet: Free outstanding DMA buffers on dmaengine stop
In the dmaengine path the driver pre-submits RX buffers and holds
in-flight TX buffers whose SKBs are DMA-mapped by the driver and freed
only in the completion callbacks. On ndo_stop() dmaengine_terminate_sync()
aborts these descriptors without running their callbacks, and the driver
then frees only the ring shells, leaking every SKB still owned by the
engine and its DMA mapping on each ifdown. With 128 RX buffers pre-posted
per channel, the mapping leak can eventually exhaust a limited IOMMU
aperture.
Cl
In the Linux kernel, the following vulnerability has been resolved:
net: team: stop reusing skb after queue override
A nonzero dev_queue_xmit() result does not return ownership of the skb.
When an override port's qdisc drops it, the queue override helper used to
try another port or the mode transmit op with the freed skb.
Return the handoff decision separately from transmit success. Select only
the first override port under RCU and stop after handing it the skb,
regardless of the lower transmit result. Keep the existing success and
drop accounting.
BUG: KASAN: slab-use-after-free in sk_skb_reason_drop
Write of size 4 by task poc/5040
net: team: free skb when broadcast has no txable port
In the Linux kernel, the following vulnerability has been resolved:
net: team: free skb when broadcast has no txable port
bc_transmit() sends the original skb through the last txable port.
When no port is txable, it returns false without consuming the skb, but
team_xmit() still returns NETDEV_TX_OK. AF_PACKET sends then retain the
skb and its socket write-memory charge.
A TX-enabled, link-down port keeps the broadcast transmit op installed.
Carrier can stay up through a second link-up, TX-disabled port or be
forced on by userspace. Free the original skb on the no-port path while
leaving the existing drop accounting intact.
Discovered by S
openvswitch: fix soft lockup in the netlink flow dump
In the Linux kernel, the following vulnerability has been resolved:
openvswitch: fix soft lockup in the netlink flow dump
A production compute node carrying a few thousand datapath flows hit a
soft lockup inside a single netlink flow dump and panicked.
ovs_flow_cmd_dump() calls ovs_flow_stats_get() for every flow it
emits, and that releases stats->lock with spin_unlock_bh() once per
CPU that has touched the flow. Every release is a local_bh_enable(),
and each one runs the pending softirq backlog in the dumping thread's
own context.
The skb bounds the flows one callback emits, but not the softirq work
it absorbs. On a CPU that carries the
optee: register TEE devices only once fully initialized
In the Linux kernel, the following vulnerability has been resolved:
optee: register TEE devices only once fully initialized
optee_probe() called tee_device_register() on both the client and the
supplicant device before the rest of struct optee had been initialized.
tee_device_register() calls cdev_device_add(), which does two things at
once: it creates /dev/tee0 and /dev/teepriv0, and it links the device
into the tee class so that class_find_device() can find it. From that
moment on the device is reachable both from user space via tee_open()
and from kernel space via tee_client_open_context(). The only gate in
teedev_open() is tee_device_g
power: sequencing: pcie-m2: Fix leaking array from of_regulator_bulk_get_all()
In the Linux kernel, the following vulnerability has been resolved:
power: sequencing: pcie-m2: Fix leaking array from of_regulator_bulk_get_all()
of_regulator_bulk_get_all() allocates the consumers array and hands it to
the caller, who is expected to free it at an appropriate time.
pwrseq-pcie-m2.c never did, leading to a memory leak.
Add an explicit kfree() for the consumers array.
regulator: ltc3676: don't read the write-only HRST and CLIRQ registers
In the Linux kernel, the following vulnerability has been resolved:
regulator: ltc3676: don't read the write-only HRST and CLIRQ registers
HRST (0x1e) and CLIRQ (0x1f) are write-only command strobes. Writing HRST
triggers a hard reset of the chip and writing CLIRQ clears the interrupt;
reading them returns nothing useful, and the read itself fires the command.
The result is that a plain register dump resets the board:
cat /sys/kernel/debug/regmap/2-003c/registers
walks every readable register, hits HRST, and the board reboots.
Split the callback back in two so HRST and CLIRQ stay writable but are no
longer readable. The readable range
regulator: of: fill in supply names in of_regulator_bulk_get_all()
In the Linux kernel, the following vulnerability has been resolved:
regulator: of: fill in supply names in of_regulator_bulk_get_all()
of_regulator_bulk_get_all() returns an array it allocated itself, and
fills in only the consumer of each entry. Every other way of getting a
bulk array has the supply name set, because the caller provides it, and
the core expects it to be there: regulator_bulk_enable() prints it when
a supply fails to enable, so a caller that hands such an array to it
dereferences uninitialised memory on that path.
Copy each name into the array's own allocation, right behind the
entries, so that it shares the array's lifeti
regulator: tps6594-regulator: Fix n_linear_ranges for TPS65224 BUCK2-4
In the Linux kernel, the following vulnerability has been resolved:
regulator: tps6594-regulator: Fix n_linear_ranges for TPS65224 BUCK2-4
The TPS65224 BUCK2, BUCK3 and BUCK4 descriptors pass 4 as
n_linear_ranges, but tps65224_bucks_2_3_4_ranges[] only has two
entries, covering selectors 0x00-0x45.
The linear range helpers loop over n_linear_ranges entries, so any
lookup of a selector above 0x45 reads past the end of the array and
treats whatever follows it as two more ranges. This happens on the
normal registration path when the core checks the voltage constraints
against every selector. TPS652G1 uses the same descriptors and is
affected
scsi: ch: Do not keep references to data transfer element devices
In the Linux kernel, the following vulnerability has been resolved:
scsi: ch: Do not keep references to data transfer element devices
ch_readconfig() looks up the scsi_device of every data transfer element
whose SCSI id the changer reports in READ ELEMENT STATUS, and stores it in
ch->dt[]. scsi_device_lookup() takes a reference, and nothing ever drops
it: ch_destroy() frees the array with kfree(). ch->dt[] is read nowhere
else - it only supplies the vendor, model and revision printed in the same
loop.
Once such a drive is removed, its scsi_device can never be released. It
stays on the host's device list at its address, so a new device ther
riscv: entry: gate shadow call stack reload on sstatus.SPP, not tp
In the Linux kernel, the following vulnerability has been resolved:
riscv: entry: gate shadow call stack reload on sstatus.SPP, not tp
Under CONFIG_SHADOW_CALL_STACK, handle_exception() reloads the kernel
shadow call stack pointer (gp) only when the trap came from userspace.
It made that decision with scs_load_current_if_task_changed, which
compares the trap-time tp (read back from sscratch into s5) against the
current tp:
beq \prev, tp, _skip_scs
scs_load_current
_skip_scs:
tp is a user-writable register. A user task that sets tp to the
linear-map address of its own task_struct (¤t) before trapping
makes the comparison succeed (
riscv: errata: select RISCV_ALTERNATIVE_EARLY for THEAD GHOSTWRITE
In the Linux kernel, the following vulnerability has been resolved:
riscv: errata: select RISCV_ALTERNATIVE_EARLY for THEAD GHOSTWRITE
errata_probe_ghostwrite() only marks the CPU as vulnerable when it is
called at the RISCV_ALTERNATIVES_EARLY_BOOT stage, and the mitigation
in ghostwrite_enable_mitigation() only takes effect if the vulnerable
state was recorded before the boot alternatives are patched.
The early boot stage is only executed when CONFIG_RISCV_ALTERNATIVE_EARLY
is enabled, which currently is only selected by ERRATA_THEAD_MAE. In a
kernel built with ERRATA_THEAD_GHOSTWRITE=y but ERRATA_THEAD_MAE=n, the
early alternatives never
riscv: futex: untag the user pointer before the atomic access
In the Linux kernel, the following vulnerability has been resolved:
riscv: futex: untag the user pointer before the atomic access
access_ok() checks untagged_addr(uaddr), but arch_futex_atomic_op_inuser()
and futex_atomic_cmpxchg_inatomic() hand the raw uaddr to the inline asm
amoswap/amoadd/.../lr.w+sc.w through the "+m" (*uaddr) operand. When the
tagged address ABI is enabled (CONFIG_RISCV_ISA_SUPM, prctl
PR_SET_TAGGED_ADDR_CTRL with PMLEN != 0), those two addresses differ: a
user pointer whose top PMLEN bits hold a tag passes access_ok() after
untagging, but the atomic is then performed on the still-tagged raw
address.
Supervisor-mode
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: Serialize dead-device detachment
Rebinding an HCI socket after its controller is unregistered can race
monitor control replay and crash the kernel. hci_sock_bind() clears
hci_pi(sk)->hdev and drops the device reference under only the socket
lock, whereas send_monitor_control_replay() holds hci_sk_list.lock for
reading.
Replay can observe a non-NULL hdev, then bind can clear it and drop the
last reference before create_monitor_ctrl_open() reads hdev->id. This
can cause a NULL pointer dereference if the pointer is reloaded, or a
use-after-free if the old
Bluetooth: hci_sync: Fix command skb lifetime during scan setup
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix command skb lifetime during scan setup
During PA sync scan setup, hci_le_set_ext_scan_param_sync() gets the
address used for the PA_LINK lookup from hci_sent_cmd_data(). The
returned pointer borrows storage from sent_cmd or req_skb, without
holding a reference to either skb.
The scan worker runs on req_workqueue while hci_cmd_work() runs on the
separate device workqueue. After the scan worker loads sent_cmd, the
command worker can free and replace it before hci_sent_cmd_data()
dereferences the skb. The command payload can also be freed between
retu
Bluetooth: ISO: Reject concurrent BIS listener setup
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Reject concurrent BIS listener setup
iso_sock_listen() drops the socket lock before calling iso_listen_bis()
to preserve the hdev->lock ordering. Two concurrent listen() calls on
the same broadcast socket can therefore both observe BT_BOUND. Caller
A can attach connA and release the locks, then caller B can acquire
them and attach connB before A publishes BT_LISTEN.
__iso_chan_add() checks whether connB already has a socket, but not
whether the socket already has a connection. The second attachment
overwrites iso_pi(sk)->conn, leaking the connA reference an
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Serialize concurrent connect calls
iso_sock_connect() checks the socket state before taking the socket lock
and drops the lock again before setting up a connection. Two callers can
both pass the admission check while the socket is open or bound.
Caller A can copy its destination for route selection, then caller B can
replace the socket destination before A binds or connects the CIS. A
then uses B's destination with the route selected for its own request.
B can also proceed after A attaches a connection and sets BT_CONNECT.
For deferred BIS setup, B can bind