net: bridge: fix nd_tbl NULL dereference when IPv6 is disabled
In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix nd_tbl NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, the nd_tbl is never
initialized because inet6_init() exits before ndisc_init() is called
which initializes it. Then, if neigh_suppress is enabled and an ICMPv6
Neighbor Discovery packet reaches the bridge, br_do_suppress_nd() will
dereference ipv6_stub->nd_tbl which is NULL, passing it to
neigh_lookup(). This causes a kernel NULL pointer dereference.
BUG: kernel NULL pointer dereference, address: 0000000000000268
Oops: 0000 [#1] PREEMPT SMP NOPTI
[...]
RIP:
In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_ife: Fix metalist update behavior
Whenever an ife action replace changes the metalist, instead of
replacing the old data on the metalist, the current ife code is appending
the new metadata. Aside from being innapropriate behavior, this may lead
to an unbounded addition of metadata to the metalist which might cause an
out of bounds error when running the encode op:
[ 138.423369][ C1] ==================================================================
[ 138.424317][ C1] BUG: KASAN: slab-out-of-bounds in ife_tlv_meta_encode (net/ife/ife.c:168)
[ 138.424
blktrace: fix __this_cpu_read/write in preemptible context
In the Linux kernel, the following vulnerability has been resolved:
blktrace: fix __this_cpu_read/write in preemptible context
tracing_record_cmdline() internally uses __this_cpu_read() and
__this_cpu_write() on the per-CPU variable trace_cmdline_save, and
trace_save_cmdline() explicitly asserts preemption is disabled via
lockdep_assert_preemption_disabled(). These operations are only safe
when preemption is off, as they were designed to be called from the
scheduler context (probe_wakeup_sched_switch() / probe_wakeup()).
__blk_add_trace() was calling tracing_record_cmdline(current) early in
the blk_tracer path, before ring buffer reservati
nfc: rawsock: cancel tx_work before socket teardown
In the Linux kernel, the following vulnerability has been resolved:
nfc: rawsock: cancel tx_work before socket teardown
In rawsock_release(), cancel any pending tx_work and purge the write
queue before orphaning the socket. rawsock_tx_work runs on the system
workqueue and calls nfc_data_exchange which dereferences the NCI
device. Without synchronization, tx_work can race with socket and
device teardown when a process is killed (e.g. by SIGKILL), leading
to use-after-free or leaked references.
Set SEND_SHUTDOWN first so that if tx_work is already running it will
see the flag and skip transmitting, then use cancel_work_sync to wait
for any
net: phy: register phy led_triggers during probe to avoid AB-BA deadlock
In the Linux kernel, the following vulnerability has been resolved:
net: phy: register phy led_triggers during probe to avoid AB-BA deadlock
There is an AB-BA deadlock when both LEDS_TRIGGER_NETDEV and
LED_TRIGGER_PHY are enabled:
[ 1362.049207] [<8054e4b8>] led_trigger_register+0x5c/0x1fc <-- Trying to get lock "triggers_list_lock" via down_write(&triggers_list_lock);
[ 1362.054536] [<80662830>] phy_led_triggers_register+0xd0/0x234
[ 1362.060329] [<8065e200>] phy_attach_direct+0x33c/0x40c
[ 1362.065489] [<80651fc4>] phylink_fwnode_phy_connect+0x15c/0x23c
[ 1362.071480] [<8066ee18>] mtk_open+0x7c/0xba0
[ 1362.075849] [<806d714c
In the Linux kernel, the following vulnerability has been resolved:
wifi: radiotap: reject radiotap with unknown bits
The radiotap parser is currently only used with the radiotap
namespace (not with vendor namespaces), but if the undefined
field 18 is used, the alignment/size is unknown as well. In
this case, iterator->_next_ns_data isn't initialized (it's
only set for skipping vendor namespaces), and syzbot points
out that we later compare against this uninitialized value.
Fix this by moving the rejection of unknown radiotap fields
down to after the in-namespace lookup, so it will really use
iterator->_next_ns_data only for vendor namespa
In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: validate USB endpoints
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio
can: mcp251x: fix deadlock in error path of mcp251x_open
In the Linux kernel, the following vulnerability has been resolved:
can: mcp251x: fix deadlock in error path of mcp251x_open
The mcp251x_open() function call free_irq() in its error path with the
mpc_lock mutex held. But if an interrupt already occurred the
interrupt handler will be waiting for the mpc_lock and free_irq() will
deadlock waiting for the handler to finish.
This issue is similar to the one fixed in commit 7dd9c26bd6cf ("can:
mcp251x: fix deadlock if an interrupt occurs during mcp251x_open") but
for the error path.
To solve this issue move the call to free_irq() after the lock is
released. Setting `priv->force_quit = 1` before
drbd: fix "LOGIC BUG" in drbd_al_begin_io_nonblock()
In the Linux kernel, the following vulnerability has been resolved:
drbd: fix "LOGIC BUG" in drbd_al_begin_io_nonblock()
Even though we check that we "should" be able to do lc_get_cumulative()
while holding the device->al_lock spinlock, it may still fail,
if some other code path decided to do lc_try_lock() with bad timing.
If that happened, we logged "LOGIC BUG for enr=...",
but still did not return an error.
The rest of the code now assumed that this request has references
for the relevant activity log extents.
The implcations are that during an active resync, mutual exclusivity of
resync versus application IO is not guaranteed. And a p
In the Linux kernel, the following vulnerability has been resolved:
x86/efi: defer freeing of boot services memory
efi_free_boot_services() frees memory occupied by EFI_BOOT_SERVICES_CODE
and EFI_BOOT_SERVICES_DATA using memblock_free_late().
There are two issue with that: memblock_free_late() should be used for
memory allocated with memblock_alloc() while the memory reserved with
memblock_reserve() should be freed with free_reserved_area().
More acutely, with CONFIG_DEFERRED_STRUCT_PAGE_INIT=y
efi_free_boot_services() is called before deferred initialization of the
memory map is complete.
Benjamin Herrenschmidt reports that this causes
net: sched: avoid qdisc_reset_all_tx_gt() vs dequeue race for lockless qdiscs
In the Linux kernel, the following vulnerability has been resolved:
net: sched: avoid qdisc_reset_all_tx_gt() vs dequeue race for lockless qdiscs
When shrinking the number of real tx queues,
netif_set_real_num_tx_queues() calls qdisc_reset_all_tx_gt() to flush
qdiscs for queues which will no longer be used.
qdisc_reset_all_tx_gt() currently serializes qdisc_reset() with
qdisc_lock(). However, for lockless qdiscs, the dequeue path is
serialized by qdisc_run_begin/end() using qdisc->seqlock instead, so
qdisc_reset() can run concurrently with __qdisc_run() and free skbs
while they are still being dequeued, leading to UAF.
This can easily be
nfc: nci: free skb on nci_transceive early error paths
In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: free skb on nci_transceive early error paths
nci_transceive() takes ownership of the skb passed by the caller,
but the -EPROTO, -EINVAL, and -EBUSY error paths return without
freeing it.
Due to issues clearing NCI_DATA_EXCHANGE fixed by subsequent changes
the nci/nci_dev selftest hits the error path occasionally in NIPA,
and kmemleak detects leaks:
unreferenced object 0xff11000015ce6a40 (size 640):
comm "nci_dev", pid 3954, jiffies 4295441246
hex dump (first 32 bytes):
6b 6b 6b 6b 00 a4 00 0c 02 e1 03 6b 6b 6b 6b 6b kkkk.......kkkkk
6b 6b 6b 6b 6b 6
wifi: cfg80211: cancel rfkill_block work in wiphy_unregister()
In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: cancel rfkill_block work in wiphy_unregister()
There is a use-after-free error in cfg80211_shutdown_all_interfaces found
by syzkaller:
BUG: KASAN: use-after-free in cfg80211_shutdown_all_interfaces+0x213/0x220
Read of size 8 at addr ffff888112a78d98 by task kworker/0:5/5326
CPU: 0 UID: 0 PID: 5326 Comm: kworker/0:5 Not tainted 6.19.0-rc2 #2 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Workqueue: events cfg80211_rfkill_block_work
Call Trace:
<TASK>
dump_stack_lvl+0x116/0x1f0
print_report+0xcd/0x630
ka
nfc: nci: complete pending data exchange on device close
In the Linux kernel, the following vulnerability has been resolved:
nfc: nci: complete pending data exchange on device close
In nci_close_device(), complete any pending data exchange before
closing. The data exchange callback (e.g.
rawsock_data_exchange_complete) holds a socket reference.
NIPA occasionally hits this leak:
unreferenced object 0xff1100000f435000 (size 2048):
comm "nci_dev", pid 3954, jiffies 4295441245
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
27 00 01 40 00 00 00 00 00 00 00 00 00 00 00 00 '..@............
backtrace (crc ec2b3c5):
__kmalloc_noprof+0x4db/
ALSA: usb-audio: Use correct version for UAC3 header validation
In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Use correct version for UAC3 header validation
The entry of the validators table for UAC3 AC header descriptor is
defined with the wrong protocol version UAC_VERSION_2, while it should
have been UAC_VERSION_3. This results in the validator never matching
for actual UAC3 devices (protocol == UAC_VERSION_3), causing their
header descriptors to bypass validation entirely. A malicious USB
device presenting a truncated UAC3 header could exploit this to cause
out-of-bounds reads when the driver later accesses unvalidated
descriptor fields.
The bug was introduc
In the Linux kernel, the following vulnerability has been resolved:
net: usb: kaweth: validate USB endpoints
The kaweth driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints.
can: ems_usb: ems_usb_read_bulk_callback(): check the proper length of a message
In the Linux kernel, the following vulnerability has been resolved:
can: ems_usb: ems_usb_read_bulk_callback(): check the proper length of a message
When looking at the data in a USB urb, the actual_length is the size of
the buffer passed to the driver, not the transfer_buffer_length which is
set by the driver as the max size of the buffer.
When parsing the messages in ems_usb_read_bulk_callback() properly check
the size both at the beginning of parsing the message to make sure it is
big enough for the expected structure, and at the end of the message to
make sure we don't overflow past the end of the buffer for the next
message.
ipv6: fix NULL pointer deref in ip6_rt_get_dev_rcu()
In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix NULL pointer deref in ip6_rt_get_dev_rcu()
l3mdev_master_dev_rcu() can return NULL when the slave device is being
un-slaved from a VRF. All other callers deal with this, but we lost
the fallback to loopback in ip6_rt_pcpu_alloc() -> ip6_rt_get_dev_rcu()
with commit 4832c30d5458 ("net: ipv6: put host and anycast routes on
device with address").
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:ip6_rt_pcpu_alloc (net/ipv6/route.c:1418)
Call Trace:
ip6_pol_route (net/ipv6/route.c:2318)
fib6_rule_lookup (net/ipv6/fib6_rules.
smb: client: Don't log plaintext credentials in cifs_set_cifscreds
In the Linux kernel, the following vulnerability has been resolved:
smb: client: Don't log plaintext credentials in cifs_set_cifscreds
When debug logging is enabled, cifs_set_cifscreds() logs the key
payload and exposes the plaintext username and password. Remove the
debug log to avoid exposing credentials.