wifi: rtlwifi: rtl8192du: check QoS TID before indexing tids
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: check QoS TID before indexing tids
rtl92du_tx_fill_desc() uses ieee80211_get_tid() to read the QoS TID
from the 802.11 header and then uses it as an index into
sta_entry->tids[]. ieee80211_get_tid() returns the low 4-bit QoS TID
value, so the result can be in the range 0..15.
rtlwifi only allocates MAX_TID_COUNT entries for sta_entry->tids[], and
MAX_TID_COUNT is 9. A QoS TID greater than 8 therefore indexes past the
aggregation state array. Keep the default RTL_AGG_STOP state for
out-of-range TIDs, matching rtl92cu_tx_fill_desc().
This issue was
wifi: rtlwifi: rtl8192du: Fix possible memory leak in rtl92du_init_sw_vars()
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: Fix possible memory leak in rtl92du_init_sw_vars()
The memory allocated inside rtl92du_init_shared_data() is not freed in
any of the subsequent error paths in rtl92du_init_sw_vars().
Fix that by adding a call to rtl92du_deinit_shared_data() in the error
path.
wifi: rtw88: Fix potential memory leak in rtw_txq_push_skb()
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: Fix potential memory leak in rtw_txq_push_skb()
The skb passed to the rtw_hci_tx_write() is expected to be freed when
the function fails, but the error path in rtw_txq_push_skb() does not
free the skb before returning. This can lead to a memory leak in
rtw_txq_push() where a dequeued skb is passed to rtw_txq_push_skb().
wifi: rtw88: pci: fix resource leak on failed NAPI setup
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: pci: fix resource leak on failed NAPI setup
rtw_pci_probe() allocates PCI resources through
rtw_pci_setup_resource() before it sets up NAPI. If
rtw_pci_napi_init() fails, the error path jumps straight to
err_pci_declaim and skips rtw_pci_destroy(), leaving the PCI
resources allocated by rtw_pci_setup_resource() behind.
Add a dedicated cleanup label for the NAPI setup failure path so probe
destroys the PCI resources.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing current
mainline k
wifi: rtw89: pci: add .shutdown callback to stop rfkill polling on reboot
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: add .shutdown callback to stop rfkill polling on reboot
Since the hardware rfkill polling was introduced, arm64 platforms can
panic with an asynchronous SError during warm reboot:
SError Interrupt on CPU8, code 0x00000000be000011 -- SError
Workqueue: events_power_efficient rfkill_poll [rfkill]
rtw89_pci_ops_read8+0x94/0x160 [rtw89_pci]
rtw89_core_rfkill_poll+0x50/0x1e0 [rtw89_core]
rtw89_ops_rfkill_poll+0x40/0x68 [rtw89_core]
ieee80211_rfkill_poll+0x3c/0x70 [mac80211]
cfg80211_rfkill_poll+0x40/0x2a0 [cfg80211]
rfkill_poll+0x30/
wifi: mt76: mt7615: avoid waiting for mac work under the mt76 mutex
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7615: avoid waiting for mac work under the mt76 mutex
mt7615_suspend() acquired the mt76 mutex and then called
cancel_delayed_work_sync() on mac_work. mt7615_mac_work() acquires the
same mutex via mt7615_mutex_acquire() at the top of the worker, so if
mac_work is already running and blocked on the mutex, the suspend path
deadlocks waiting for the work it holds the mutex against.
Flush scan_work and mac_work before taking the mutex, matching the
suspend paths in mt7921 and mt7925. scan_work only takes the mt76
spinlock, but moving it keeps the sequence consi
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
mt7915_mcu_get_eeprom() copies a fixed EFUSE block into the driver's
dev->mt76.eeprom.data buffer at the offset reported by the MCU response
(res->addr, a device-controlled __le32) without checking it against the
buffer size. A malicious or malfunctioning device can report an arbitrary
address and drive a 16-byte out-of-bounds write past eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before deriving the destination pointer. Devices that echo the requested
in-bou
wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy
mt7996_mcu_get_eeprom() derives the destination of the EFUSE/EXT block
copy from the address reported by the MCU response (event->addr, a
device-controlled __le32) and clamps only the copy length, never the
destination offset into dev->mt76.eeprom.data. A malicious or
malfunctioning device can report an arbitrary address and drive an
out-of-bounds write of up to MT7996_EXT_EEPROM_BLOCK_SIZE bytes past
eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before derivin
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: validate default EEPROM firmware size
The default EEPROM firmware is parsed and copied as a full EEPROM
without checking its length. A truncated file can make the driver
read beyond the firmware buffer during variant validation or the
fallback copy.
Reject files shorter than MT7996_EEPROM_SIZE before parsing or
copying the firmware.
In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: flush works in dependency order
virtio_vsock_remove() stops the virtqueues and then flushes each work
item before freeing the enclosing virtio_vsock. The current order does
not account for dependencies between those items: tx_work may queue
send_pkt_work, and send_pkt_work may queue rx_work.
In particular, send_pkt_work can set restart_rx and release tx_lock.
The remove path can then stop the queues and flush rx_work before
send_pkt_work queues it. Although the later send_pkt_work flush waits
for that producer to finish, nothing waits for the newly queued r
w1: ds28e17: reject an oversize length on an I2C block read
In the Linux kernel, the following vulnerability has been resolved:
w1: ds28e17: reject an oversize length on an I2C block read
w1_f19_i2c_master_transfer() is the master_xfer for the DS28E17 1-Wire
to I2C bridge. On an I2C_M_RECV_LEN read, it takes the length from the
device. The downstream slave puts a length byte in buf[0]. The driver
then reads that many bytes into buf[1] with w1_f19_i2c_read().
buf[0] is controlled by the device and can be 0 to 255.
w1_f19_i2c_read() only rejects a zero count. The caller buffer is
I2C_SMBUS_BLOCK_MAX + 2, so 34 bytes. A length above 32 makes the read
run past it, up to about 222 bytes out of bounds.
In the Linux kernel, the following vulnerability has been resolved:
tpm: tpm_i2c_nuvoton: disable IRQ on wait timeout
i2c_nuvoton_wait_for_stat() enables the IRQ before waiting for the
interrupt handler to report a status change. If the wait times out, or is
interrupted before the handler runs, the function returns without
balancing the enable_irq() call.
Disable the IRQ before leaving the failed wait path. Also preserve an
interrupted wait's original error code instead of converting it to
-ETIMEDOUT inside the helper.
smack: fix cred UAF in smack_file_send_sigiotask()
In the Linux kernel, the following vulnerability has been resolved:
smack: fix cred UAF in smack_file_send_sigiotask()
When inspecting the credentials of another task, objective credentials
(->real_cred, accessed with __task_cred()) must always be used.
Accessing ->cred on a non-current task is forbidden unless that task is
being created or destroyed; a task is allowed to change its own ->cred
pointer with no synchronization, and changing ->cred should only affect the
current syscall.
smack_file_send_sigiotask() was accessing both sets of credentials: First
tsk->cred, then __task_cred(tsk).
Fix it, always access the objective credentials
ksmbd: fix use-after-free in oplock break notification
In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in oplock break notification
smb2_oplock_break_noti() reads opinfo->conn without any lock and
dereferences it after two allocations which may sleep. When the
durable handle owning the oplock is disconnected, session_fd_check()
clears opinfo->conn and drops its conn reference under ci->m_lock, and
the last ksmbd_conn_put() frees the connection. A break triggered by
another connection that races with the teardown can then resurrect the
freed connection: ksmbd_conn_get() is a plain atomic_inc, and the
queued break work later dereferences the stale c
vlan: fix skb_under_panic and races when toggling HW VLAN offload
In the Linux kernel, the following vulnerability has been resolved:
vlan: fix skb_under_panic and races when toggling HW VLAN offload
Toggling hardware VLAN TX offload (NETIF_F_HW_VLAN_CTAG_TX or
NETIF_F_HW_VLAN_STAG_TX) on a lower device invokes vlan_transfer_features(),
which dynamically changed vlandev->hard_header_len.
This causes two issues:
1. Lockless TX paths (e.g. packet_snd in af_packet.c, ip6_finish_output2)
read dev->hard_header_len without holding RTNL lock. Mutating
hard_header_len dynamically under RTNL creates a data race where upper
layers reserve insufficient headroom based on a stale hard_header_len,
resultin
xhci: dbgtty: Fix unregister on tty_register_driver() failure
In the Linux kernel, the following vulnerability has been resolved:
xhci: dbgtty: Fix unregister on tty_register_driver() failure
If tty_register_driver() fails, it drops the reference, but fails to set
the global dbc_tty_driver to NULL, causing the unregister to be called
again when module exits.
On module unload dbc_tty_exit() only gates its cleanup on the driver
pointer being non-NULL, so it operates on the already-freed driver:
module_init(xhci_hcd_init)
xhci_hcd_init()
xhci_dbc_init() [return value ignored]
dbc_tty_init()
tty_register_driver() fails
tty_drive
In the Linux kernel, the following vulnerability has been resolved:
crypto: qcom-rng - Allow zero as a random number
Zero is a valid random number and needs to be allowed. Otherwise the
output is distinguishable from random.
In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: vsie: zero stale crypto bits
When shadowing crypto access bits from a format0 apcb (crycb 0 or 1),
the bits 64..255 are unchanged from whatever is in the vsie page in the
crycb and thus in the apcb. This gives a nested guest potential access
to a device no longer available. Zero out the remaining bits.
io_uring: defer eventfd signaling when queued from a wakeup handler
In the Linux kernel, the following vulnerability has been resolved:
io_uring: defer eventfd signaling when queued from a wakeup handler
io_req_local_work_add() signals the CQ ring eventfd inline when it is the
one to push the first entry onto ->work_list. For DEFER_TASKRUN rings that
add is frequently done from a waitqueue wakeup handler, where an
arbitrary waitqueue lock is held.
eventfd_signal_mask() only refuses to recurse when current->in_eventfd
is set, but that bit is set by eventfd_signal_mask() itself. If the wake
chain starts somewhere else, signal goes out inline and can feed back
into epoll.
Add IOU_F_TWQ_IN_WAKE, set it on the
HID: core: fix number/pointer type confusion on long items
In the Linux kernel, the following vulnerability has been resolved:
HID: core: fix number/pointer type confusion on long items
When fetch_item() is called by hid_scan_report() on an item with
HID_ITEM_TAG_LONG, it stores a pointer to the item data in
item->data.longdata instead of storing a value directly in
item->data.{u8/u16/u32}.
When item_udata() or item_sdata() encounters such an item, it incorrectly
assumes that the item is in short format, and therefore returns the lower
part of a kernel pointer reinterpreted as a number.
When a HID device is connected whose descriptor contains a
HID_GLOBAL_ITEM_TAG_REPORT_SIZE encoded in long form