netfilter: nf_conntrack: destroy stale expectfn expectations on unregister
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack: destroy stale expectfn expectations on unregister
NAT helpers such as nf_nat_h323 store a raw pointer to module text in
exp->expectfn (e.g. ip_nat_q931_expect). nf_ct_helper_expectfn_unregister()
only unlinks the callback descriptor and never walks the expectation table,
so an expectation pending at module removal survives with a dangling
exp->expectfn into freed module text.
When the expected connection arrives, init_conntrack() invokes
exp->expectfn(), now a stale pointer into the unloaded module. Reproduced
on a KASAN build by loading the H.323
i2c: qcom-cci: Fix NULL pointer dereference in cci_remove()
In the Linux kernel, the following vulnerability has been resolved:
i2c: qcom-cci: Fix NULL pointer dereference in cci_remove()
On all modern platforms Qualcomm CCI controller provides two I2C masters,
and on particular boards only one I2C master may be initialized, and in
such cases the device unbinding or driver removal causes a NULL pointer
dereference, because cci_halt() is called for all two I2C masters, but
a completion is initialized only for the single enabled master:
% rmmod i2c-qcom-cci
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
<snip>
Call trace:
__wait_for_common+0x1
net: bonding: fix NULL pointer dereference in bond_do_ioctl()
In the Linux kernel, the following vulnerability has been resolved:
net: bonding: fix NULL pointer dereference in bond_do_ioctl()
In bond_do_ioctl(), slave_dev is obtained via __dev_get_by_name() which
can return NULL if the requested interface name does not exist. However,
the subsequent slave_dbg() call is placed before the NULL check:
slave_dev = __dev_get_by_name(net, ifr->ifr_slave);
slave_dbg(bond_dev, slave_dev, "slave_dev=%p:\n", slave_dev); //here
if (!slave_dev)
return -ENODEV;
The slave_dbg() macro expands to netdev_dbg(bond_dev, "(slave %s): " fmt,
(slave_dev)->name, ...) which unconditionally dereferences
slimbus: qcom-ngd-ctrl: Register callbacks after creating the ngd
In the Linux kernel, the following vulnerability has been resolved:
slimbus: qcom-ngd-ctrl: Register callbacks after creating the ngd
When the remoteproc starts in parallel with the NGD driver being probed,
or the remoteproc is already up when the PDR lookup is being registered,
or in the theoretical event that we get an interrupt from the hardware,
these callbacks will operate on uninitialized data. This result in
issues to boot the affected boards.
One such example can be seen in the following fault, where
qcom_slim_ngd_ssr_pdr_notify() schedules work on the NULL ngd_up_work.
[ 21.858578] ------------[ cut here ]------------
[ 21.85
slimbus: qcom-ngd-ctrl: Avoid ABBA on tx_lock/ctrl->lock
In the Linux kernel, the following vulnerability has been resolved:
slimbus: qcom-ngd-ctrl: Avoid ABBA on tx_lock/ctrl->lock
During the SSR/PDR down notification the tx_lock is taken with the
intent to provide synchronization with active DMA transfers.
But during this period qcom_slim_ngd_down() is invoked, which ends up in
slim_report_absent(), which takes the slim_controller lock. In multiple
other codepaths these two locks are taken in the opposite order (i.e.
slim_controller then tx_lock).
The result is a lockdep splat, and a possible deadlock:
rprocctl/449 is trying to acquire lock:
ffff00009793e620 (&ctrl->lock){+.+.}-{4:4}, at
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Fix out-of-bounds read in dp_get_eq_aux_rd_interval()
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
(ch
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Use krealloc_array() in dal_vector_reserve()
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
(cherry picked from commit 37668568641ccc4cc1dbca4923d0a16609dd5707)
In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Do not fill_pool() if pi_blocked_on
On RT enabled kernels, fill_pool() ends up calling rtlock_lock(), which
asserts if current::pi_blocked_on is set, because a task can obviously only
block on one lock as otherwise the priority inheritenace chain gets
corrupted.
Prevent this by expanding the conditional to take current::pi_blocked_on
into account.
agp/amd64: Fix broken error propagation in agp_amd64_probe()
In the Linux kernel, the following vulnerability has been resolved:
agp/amd64: Fix broken error propagation in agp_amd64_probe()
A NULL pointer dereference was observed in the AMD64 AGP driver when
running in a virtualized environment (e.g. qemu/kvm) without a physical
AMD northbridge. The crash occurs in amd64_fetch_size() when attempting
to dereference the pointer returned by node_to_amd_nb(0).
The root cause of this crash is broken error propagation in
agp_amd64_probe(): When no AMD northbridges are found, cache_nbs()
correctly returns -ENODEV. However, the probe function erroneously
checks the return value against exactly -1, rather th
nilfs2: reject zero bd_oblocknr in nilfs_ioctl_mark_blocks_dirty()
In the Linux kernel, the following vulnerability has been resolved:
nilfs2: reject zero bd_oblocknr in nilfs_ioctl_mark_blocks_dirty()
nilfs_ioctl_mark_blocks_dirty() uses bd_oblocknr to detect dead blocks
by comparing it with the current block number bd_blocknr. If they differ,
the block is considered dead and skipped.
However, bd_oblocknr should never be 0 since block 0 typically stores the
primary superblock and is never a valid GC target block. A corrupted ioctl
request with bd_oblocknr set to 0 causes the comparison to incorrectly
match when the lookup returns -ENOENT and sets bd_blocknr to 0, bypassing
the dead block check and callin
wifi: mt76: mt7921: Place upper limit on station AID
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash
padata: Put CPU offline callback in ONLINE section to allow failure
In the Linux kernel, the following vulnerability has been resolved:
padata: Put CPU offline callback in ONLINE section to allow failure
syzbot reported the following warning:
DEAD callback error for CPU1
WARNING: kernel/cpu.c:1463 at _cpu_down+0x759/0x1020 kernel/cpu.c:1463, CPU#0: syz.0.1960/14614
at commit 4ae12d8bd9a8 ("Merge tag 'kbuild-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux")
which tglx traced to padata_cpu_dead() given it's the only
sub-CPUHP_TEARDOWN_CPU callback that returns an error.
Failure isn't allowed in hotplug states before CPUHP_TEARDOWN_CPU
so move the CPU offline callback to t
drm/amd/display: Avoid NULL dereference in dc_dmub_srv error paths
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid NULL dereference in dc_dmub_srv error paths
In dc_dmub_srv_log_diagnostic_data() and
dc_dmub_srv_enable_dpia_trace().
Both functions check:
if (!dc_dmub_srv || !dc_dmub_srv->dmub)
and then call DC_LOG_ERROR() inside that block.
DC_LOG_ERROR() uses dc_dmub_srv->ctx internally. So if
dc_dmub_srv is NULL, the logging itself can dereference a
NULL pointer and cause a crash.
Fix this by splitting the checks.
First check if dc_dmub_srv is NULL and return immediately.
Then check dc_dmub_srv->dmub and log the error only when
dc_dmub_srv is valid.
Fix
ocfs2/dlm: fix off-by-one in dlm_match_regions() region comparison
In the Linux kernel, the following vulnerability has been resolved:
ocfs2/dlm: fix off-by-one in dlm_match_regions() region comparison
The local-vs-remote region comparison loop uses '<=' instead of '<',
causing it to read one entry past the valid range of qr_regions. The
other loops in the same function correctly use '<'.
Fix the loop condition to use '<' for consistency and correctness.
tty: hvc_iucv: fix off-by-one in number of supported devices
In the Linux kernel, the following vulnerability has been resolved:
tty: hvc_iucv: fix off-by-one in number of supported devices
MAX_HVC_IUCV_LINES == HVC_ALLOC_TTY_ADAPTERS == 8.
This is the number of entries in:
static struct hvc_iucv_private *hvc_iucv_table[MAX_HVC_IUCV_LINES];
Sometimes hvc_iucv_table[] is limited by:
(a) if (num > hvc_iucv_devices) // for error detection
or
(b) for (i = 0; i < hvc_iucv_devices; i++) // in 2 places
(so these 2 don't agree; second one appears to be correct to me.)
hvc_iucv_devices can be 0..8. This is a counter.
(c) if (hvc_iucv_devices > MAX_HVC_IUCV_LINES)
If hvc_iucv_devices == 8, (a) allows the
scsi: sg: Resolve soft lockup issue when opening /dev/sgX
In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Resolve soft lockup issue when opening /dev/sgX
The parameter def_reserved_size defines the default buffer size reserved
for each Sg_fd and should be restricted to a range between 0 and 1,048,576
(see https://tldp.org/HOWTO/SCSI-Generic-HOWTO/proc.html). Although the
function sg_proc_write_dressz enforces this limit, it is possible to bypass
it by directly modifying the module parameter as shown below, which then
causes a soft lockup:
echo -1 > /sys/module/sg/parameters/def_reserved_size
exec 4<> /dev/sg0
watchdog: BUG: soft lockup - CPU#5 stuck for 26 seconds!
f2fs: protect extension_list reading with sb_lock in f2fs_sbi_show()
In the Linux kernel, the following vulnerability has been resolved:
f2fs: protect extension_list reading with sb_lock in f2fs_sbi_show()
In f2fs_sbi_show(), the extension_list, extension_count and
hot_ext_count are read without holding sbi->sb_lock. If a concurrent
sysfs store modifies the extension list via f2fs_update_extension_list(),
the show path may read inconsistent count and array contents, potentially
leading to out-of-bounds access or displaying stale data.
Fix this by holding sb_lock around the entire extension list read
and format operation.
mailbox: mailbox-test: free channels on probe error
In the Linux kernel, the following vulnerability has been resolved:
mailbox: mailbox-test: free channels on probe error
On probe error, free the previously obtained channels. This not only
prevents a leak, but also UAF scenarios because the client structure
will be removed nonetheless because it was allocated with devm.
In the Linux kernel, the following vulnerability has been resolved:
mailbox: add sanity check for channel array
Fail gracefully if there is no channel array attached to the mailbox
controller. Otherwise the later dereference will cause an OOPS which
might not be seen because mailbox controllers might instantiate very
early. Remove the comment explaining the obvious while here.
mailbox: mailbox-test: don't free the reused channel
In the Linux kernel, the following vulnerability has been resolved:
mailbox: mailbox-test: don't free the reused channel
The RX channel can be aliased to the TX channel if it has a different
MMIO. This special case needs to be handled when freeing the channels
otherwise a double-free occurs.