i3c: Fix unlocked dereference of dev->desc in i3c_device_get_supported_xfer_mode()
In the Linux kernel, the following vulnerability has been resolved:
i3c: Fix unlocked dereference of dev->desc in i3c_device_get_supported_xfer_mode()
i3c_device_get_supported_xfer_mode() uses dev->desc to obtain the
master controller. However, dev->desc must not be dereferenced unless
bus->lock is held, and this function does not take that lock.
The function only needs access to the master controller associated with
the device's bus. Use dev->bus instead, which is always valid for the
lifetime of the device and does not require dereferencing dev->desc.
i3c: master: adi: initialize the lock before enabling interrupts
In the Linux kernel, the following vulnerability has been resolved:
i3c: master: adi: initialize the lock before enabling interrupts
adi_i3c_master_probe() requests the IRQ and unmasks REG_IRQ_PENDING_CMDR
before the controller's IBI state, transfer queue list and transfer
queue lock are initialized. A pending CMDR interrupt can therefore run
adi_i3c_master_irq() and take master->xferqueue.lock before the dynamic
lock has been initialized.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the probe ordering and the IRQ path
adi_i3c_master_probe() -> adi_i3c_master_
i3c: master: Fix info leak and UAF in device unregister path
In the Linux kernel, the following vulnerability has been resolved:
i3c: master: Fix info leak and UAF in device unregister path
i3c_master_unregister_i3c_devs() clears i3cdev->dev->desc before
calling device_unregister(). During device_unregister(),
device_del() emits a KOBJ_REMOVE uevent and unbinds the driver while
the device descriptor is still expected to be valid. As a result,
i3c_device_uevent() and a racing modalias_show() can observe a NULL
desc and fall back to an uninitialized stack struct i3c_device_info,
leaking kernel stack contents in the generated modalias. Driver
.remove() callbacks may also encounter an unexpected NULL
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
i3c: master: svc: bound IBI payload to the requested max_payload_len
In the Linux kernel, the following vulnerability has been resolved:
i3c: master: svc: bound IBI payload to the requested max_payload_len
svc_i3c_master_handle_ibi() reads the IBI payload from the RX FIFO into
the IBI slot. The loop is bounded by the hardware FIFO size
(SVC_I3C_FIFO_SIZE), not by the slot size.
slot->data points into the IBI pool, which i3c_generic_ibi_alloc_pool()
sizes at max_payload_len per slot. svc_i3c_master_request_ibi() only
rejects a max_payload_len larger than SVC_I3C_FIFO_SIZE, so a driver can
request a smaller one. mctp-i3c requests 1. Each readsb() then copies the
controller RXCOUNT bytes (up to 31) with no che
i3c: renesas: Check that the transfer is valid before accessing it
In the Linux kernel, the following vulnerability has been resolved:
i3c: renesas: Check that the transfer is valid before accessing it
The Renesas I3C driver uses an asynchronous model to transfer data. It
prepares a struct renesas_i3c_xfer, enqueues it, and waits for completion.
The interrupt handler dequeues the transfer, updates/uses it, and signals
the waiting thread.
If the completion times out, the waiting thread dequeues the transfer and
free it. If an interrupt fires after that, the handler may access freed
memory, leading to crashes.
Check that the transfer is still valid before accessing it in the
interrupt handler. With it clea
Nicht bewertetEPSS 0,18%Keine Korrektur veröffentlicht
wifi: brcmfmac: Fix memory leak in brcmf_sdio_read_control()
In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix memory leak in brcmf_sdio_read_control()
The memory allocated for buf is not freed in some of the error paths in
brcmf_sdio_read_control(). Fix that by adding vfree() calls.
[arend: rework as suggested by Johannes]
Nicht bewertetEPSS 0,22%Keine Korrektur veröffentlicht
wifi: iwlwifi: dvm: fix memory leak in iwl_op_mode_dvm_start()
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: dvm: fix memory leak in iwl_op_mode_dvm_start()
In iwl_op_mode_dvm_start(), jumping to out_free_eeprom currently bypasses
the out_free_eeprom_blob label. Consequently, error paths triggered after
successfully parsing the EEPROM free priv->nvm_data but leak
priv->eeprom_blob.
Fix this memory leak by reordering the error handling labels so
that out_free_eeprom falls through to out_free_eeprom_blob.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under d
wifi: rtl8xxxu: fix use-after-free from rx_urb_wq on stop
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: fix use-after-free from rx_urb_wq on stop
rtl8xxxu arms rx_urb_wq from the RX completion path:
rtl8xxxu_rx_complete() hands the URB to rtl8xxxu_queue_rx_urb(), which
queues it on rx_urb_pending_list and, once the list grows past
RTL8XXXU_RX_URB_PENDING_WATER, schedules rx_urb_wq. The worker
rtl8xxxu_rx_urb_work() drains rx_urb_pending_list, recovers priv through
container_of, and resubmits each URB through rtl8xxxu_submit_rx_urb(),
which anchors it on rx_anchor and dereferences priv->udev.
rtl8xxxu_stop() cancels the sibling work items (c2hcmd_work, ra_wat
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
fuse: copy request headers via a stack buffer for io-uring
In the Linux kernel, the following vulnerability has been resolved:
fuse: copy request headers via a stack buffer for io-uring
The fuse-io-uring transport copies req->in.h out to the ring in
fuse_uring_copy_to_ring() and req->out.h back in fuse_uring_commit().
Both headers live inside the fuse_request slab object, whose cache
(fuse_req_cachep) is created without a usercopy whitelist, so copying
them directly to/from userspace trips CONFIG_HARDENED_USERCOPY and
panics:
usercopy: Kernel memory exposure attempt detected from SLUB object
'fuse_request' (offset 56, size 40)!
kernel BUG at mm/usercopy.c:102!
Oops: invalid opcode: 0000 [#
crypto: iaa - unmap dst before software fallback on decompress
In the Linux kernel, the following vulnerability has been resolved:
crypto: iaa - unmap dst before software fallback on decompress
On a hardware analytics error, decompress retries through the software
fallback, which writes req->dst with the CPU while it is still mapped
DMA_FROM_DEVICE. With SWIOTLB active the later dma_unmap_sg() copies the
stale bounce buffer over req->dst, corrupting the result.
Unmap before the fallback runs. The async path unmaps inline; the sync
path signals the retry with -EAGAIN so iaa_comp_adecompress() runs the
fallback after unmapping.
wifi: mwifiex: Detach sync cmd buffer on interrupted wait
In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: Detach sync cmd buffer on interrupted wait
mwifiex synchronous commands keep the caller-provided data buffer in
cmd_node->data_buf. Several callers pass stack-allocated objects there.
If wait_event_interruptible_timeout() is interrupted, the caller can
return and release that stack object while the firmware command is still
the current command. A late firmware response then reaches the normal
response handler, which can copy data through cmd_node->data_buf into the
stale stack address.
This fixes a stack corruption observed during repeated association and
d
wifi: rtlwifi: rtl8192du: check QoS TID before indexing tids
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: check QoS TID before indexing tids
rtl92du_tx_fill_desc() uses ieee80211_get_tid() to read the QoS TID
from the 802.11 header and then uses it as an index into
sta_entry->tids[]. ieee80211_get_tid() returns the low 4-bit QoS TID
value, so the result can be in the range 0..15.
rtlwifi only allocates MAX_TID_COUNT entries for sta_entry->tids[], and
MAX_TID_COUNT is 9. A QoS TID greater than 8 therefore indexes past the
aggregation state array. Keep the default RTL_AGG_STOP state for
out-of-range TIDs, matching rtl92cu_tx_fill_desc().
This issue was
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
wifi: rtlwifi: rtl8192du: Fix possible memory leak in rtl92du_init_sw_vars()
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: Fix possible memory leak in rtl92du_init_sw_vars()
The memory allocated inside rtl92du_init_shared_data() is not freed in
any of the subsequent error paths in rtl92du_init_sw_vars().
Fix that by adding a call to rtl92du_deinit_shared_data() in the error
path.
Nicht bewertetEPSS 0,22%Keine Korrektur veröffentlicht
wifi: rtw88: Fix potential memory leak in rtw_txq_push_skb()
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: Fix potential memory leak in rtw_txq_push_skb()
The skb passed to the rtw_hci_tx_write() is expected to be freed when
the function fails, but the error path in rtw_txq_push_skb() does not
free the skb before returning. This can lead to a memory leak in
rtw_txq_push() where a dequeued skb is passed to rtw_txq_push_skb().
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
wifi: rtw88: pci: fix resource leak on failed NAPI setup
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: pci: fix resource leak on failed NAPI setup
rtw_pci_probe() allocates PCI resources through
rtw_pci_setup_resource() before it sets up NAPI. If
rtw_pci_napi_init() fails, the error path jumps straight to
err_pci_declaim and skips rtw_pci_destroy(), leaving the PCI
resources allocated by rtw_pci_setup_resource() behind.
Add a dedicated cleanup label for the NAPI setup failure path so probe
destroys the PCI resources.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing current
mainline k
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
wifi: rtw89: pci: add .shutdown callback to stop rfkill polling on reboot
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: add .shutdown callback to stop rfkill polling on reboot
Since the hardware rfkill polling was introduced, arm64 platforms can
panic with an asynchronous SError during warm reboot:
SError Interrupt on CPU8, code 0x00000000be000011 -- SError
Workqueue: events_power_efficient rfkill_poll [rfkill]
rtw89_pci_ops_read8+0x94/0x160 [rtw89_pci]
rtw89_core_rfkill_poll+0x50/0x1e0 [rtw89_core]
rtw89_ops_rfkill_poll+0x40/0x68 [rtw89_core]
ieee80211_rfkill_poll+0x3c/0x70 [mac80211]
cfg80211_rfkill_poll+0x40/0x2a0 [cfg80211]
rfkill_poll+0x30/
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
wifi: mt76: mt7615: avoid waiting for mac work under the mt76 mutex
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7615: avoid waiting for mac work under the mt76 mutex
mt7615_suspend() acquired the mt76 mutex and then called
cancel_delayed_work_sync() on mac_work. mt7615_mac_work() acquires the
same mutex via mt7615_mutex_acquire() at the top of the worker, so if
mac_work is already running and blocked on the mutex, the suspend path
deadlocks waiting for the work it holds the mutex against.
Flush scan_work and mac_work before taking the mutex, matching the
suspend paths in mt7921 and mt7925. scan_work only takes the mt76
spinlock, but moving it keeps the sequence consi
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
mt7915_mcu_get_eeprom() copies a fixed EFUSE block into the driver's
dev->mt76.eeprom.data buffer at the offset reported by the MCU response
(res->addr, a device-controlled __le32) without checking it against the
buffer size. A malicious or malfunctioning device can report an arbitrary
address and drive a 16-byte out-of-bounds write past eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before deriving the destination pointer. Devices that echo the requested
in-bou
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: cancel mlo_pm_work on stop
mt7925 queues mlo_pm_work with a 5 second delay during multi-link
power-save setup and never cancels it on the stop path. If the device is
torn down inside that window, the work outlives the teardown and its timer
fires afterwards, trying to queue onto the workqueue that is already gone:
workqueue: cannot queue mt7925_mlo_pm_work [mt7925_common] on wq phy0
WARNING: kernel/workqueue.c:2283 at __queue_work+0x59/0xa0, CPU#1: swapper/1/0
call_timer_fn+0x2a/0x140
__run_timers+0x203/0x330
run_timer_softirq+0x86/0xf0
mt
wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy
In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: bound the device EEPROM address before the EFUSE copy
mt7996_mcu_get_eeprom() derives the destination of the EFUSE/EXT block
copy from the address reported by the MCU response (event->addr, a
device-controlled __le32) and clamps only the copy length, never the
destination offset into dev->mt76.eeprom.data. A malicious or
malfunctioning device can report an arbitrary address and drive an
out-of-bounds write of up to MT7996_EXT_EEPROM_BLOCK_SIZE bytes past
eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before derivin