Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend
In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb-legacy: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relyin
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
phy: qcom: snps-femto-v2: Fix possible NULL-deref on early runtime suspend
In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: snps-femto-v2: Fix possible NULL-deref on early runtime suspend
Runtime PM must be enabled before creating the PHY, since phy_create()
only enables runtime PM on the PHY device if it is already enabled on
this parent device. However, the runtime PM callbacks dereference the
hsphy instance, which is not yet ready, leaving a window where a suspend
callback may trigger a NULL pointer dereference.
Take a runtime PM usage reference with pm_runtime_get_noresume() before
enabling runtime PM and release it once the PHY has been created, so that
no runtime suspend can ru
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
phy: qcom: qmp-usb: Fix possible NULL-deref on early runtime suspend
In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usb: Fix possible NULL-deref on early runtime suspend
There is a small window where the runtime suspend callback may run
after pm_runtime_enable() and before pm_runtime_forbid(). In this
case, a crash occurs because runtime suspend/resume dereferences
qmp->phy pointer, which is not yet initialized:
`if (!qmp->phy->init_count) {`
This can also happen if user re-enables runtime-pm via the sysfs
attribute before qmp phy is initialized.
Similarly to other qcom phy drivers, introduce a qmp->phy_initialized
variable that can be used to avoid relying on th
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
md/raid5: round bitmap stripes with sector division
In the Linux kernel, the following vulnerability has been resolved:
md/raid5: round bitmap stripes with sector division
raid5_bitmap_sector_map() aligns the array range to full RAID5 stripe
widths before converting it to component sectors. That width is
chunk_sectors multiplied by the number of data disks, and it is not
always a power of two.
Reproduce with a 4-disk RAID5, 1024-sector chunks, and three data disks.
The full-stripe width is 3072 sectors. For a one-sector write at array
sector 3072, correct rounding gives array range [3072, 6144), which maps
to component range [1024, 2048). The old round_down()/round_up() logic
instead gives
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
md/raid1: don't set array_frozen in raid1_takeover()
In the Linux kernel, the following vulnerability has been resolved:
md/raid1: don't set array_frozen in raid1_takeover()
raid1_takeover() sets conf->array_frozen = 1 on the newly-allocated
r1conf and nothing ever clears it, so every I/O to the array stalls
permanently once _wait_barrier() sees it stuck at 1.
This used to be harmless: level_store() called mddev_resume() right
after pers->run(), which called raid1_quiesce(mddev, 0) and cleared
array_frozen back to 0 regardless of what raid1_takeover() set. Commit
b39f35ebe86d ("md: don't quiesce in mddev_suspend()") removed that
quiesce(mddev, 0) call, so the pre-set now sticks.
setup_conf(
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
coresight: etm4x: fix underflow for usage of (nrseqstate - 1)
In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: fix underflow for usage of (nrseqstate - 1)
According to IHI006H Embedded Trace Macrocell Architecture
Specification[0], TRCSEQEVR<n> is implemented only when
TRCIDR5.NUMSEQSTATE is 0b100, in which case n ranges from 0 to 2;
otherwise, TRCIDR5.NUMSEQSTATE is 0b000.
IOW, the number of usage in the initialisation or setting
TRCSEQEVR<n> with drvdata->nrseqstate - 1 in the loop could make
underflow issue when TRCIDR5.NUMSEQSTATE is 0b000.
Therefore, introduce nr_seq_ctrls field and untie it from nrseqstate.
As part of this introduce ETM_MAX_SEQ_TRANSITIONS
coresight: etm4x: missing cscfg_csdev_disable_active_config() in perf enable
In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: missing cscfg_csdev_disable_active_config() in perf enable
In the perf enable path, there are missing cases where
cscfg_csdev_disable_active_config() is not called:
- Branch broadcast is selected but not supported by the hardware
- etm4_enable_hw() fails
This can lead to a leak of config_desc->active_cnt.
Fix this by properly calling cscfg_csdev_disable_active_config()
in these error paths.
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
scsi: sd: Fix special_vec mempool leak when scsi_alloc_sgtables() fails
In the Linux kernel, the following vulnerability has been resolved:
scsi: sd: Fix special_vec mempool leak when scsi_alloc_sgtables() fails
sd_set_special_bvec() allocates a special payload page for UNMAP and
WRITE SAME commands. If scsi_alloc_sgtables() fails afterward in
sd_setup_unmap_cmnd() or sd_setup_write_same{10,16}_cmnd(), the SCSI
midlayer does not call uninit_command() because RQF_DONTPREP is not set
yet, leaking the page.
Call sd_uninit_command() on error, and clear RQF_SPECIAL_PAYLOAD after
freeing the page.
btrfs: defrag: fix deadlock between defrag and delalloc space reservation
In the Linux kernel, the following vulnerability has been resolved:
btrfs: defrag: fix deadlock between defrag and delalloc space reservation
While running fsstress with autodefrag and flushoncommit, hit a deadlock
due to the fact that defrag reserves delalloc space while it's holding
dirty and locked folios, besides the extent range lock. The stack traces
are the following:
[958.624] task:kworker/u50:3 state:D stack:0 pid:20365 tgid:20365 ppid:2 task_flags:0x4208060 flags:0x00080000
[958.626] Workqueue: events_unbound btrfs_async_reclaim_metadata_space [btrfs]
[958.627] Call Trace:
[958.628] <TASK>
[958.628] __
btrfs: check if root is readonly when setting posix acl
In the Linux kernel, the following vulnerability has been resolved:
btrfs: check if root is readonly when setting posix acl
For a filesystem which has btrfs read-only property set to true, all
write operations including acl and xattr should be denied. However, acl
can still be set even if btrfs ro property is true.
This happens because no function on the set_acl code path checks the root
is readonly or not. It was checked in btrfs_setxattr_trans() but got
removed in commit 353c2ea735e4 ("btrfs: remove redundant readonly root
check in btrfs_setxattr_trans")
That commit didn't check if all the callers properly check the root's
read-only fla
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
btrfs: retry verity reads for not-uptodate Merkle folios
In the Linux kernel, the following vulnerability has been resolved:
btrfs: retry verity reads for not-uptodate Merkle folios
btrfs_read_merkle_tree_page() can find a folio in the mapping that is not
uptodate. After taking the folio lock, the current code treats that state
as a read error and returns -EIO.
That can make a previous transient read failure sticky. If the failed read
left a not-uptodate folio in the mapping, later callers find that folio and
fail instead of retrying the read.
Keep the existing page-cache insertion and locking order, but retry the
Merkle item read when a not-uptodate folio is found in the mapping. Also
unloc
btrfs: zoned: flush active metadata block group at btree_writepages() start
In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: flush active metadata block group at btree_writepages() start
btree_writepages() writes the btree inode's dirty metadata in ascending
logical address order. On a zoned filesystem only one metadata and one
system block group is active for writing at a time, and
check_bg_is_active() (via btrfs_check_meta_write_pointer()) pivots the
active block group as writeback moves from one block group to the next.
If the active block group sits at a higher logical address than another
block group that also holds dirty metadata, the ascending walk reaches
the lower one firs
btrfs: zoned: don't clobber the extent buffer when zeroing it out
In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: don't clobber the extent buffer when zeroing it out
On a zoned filesystem a freed-but-still-dirty tree block is written out
as zeros (EXTENT_BUFFER_ZONED_ZEROOUT) only to keep the zone write
pointer advancing. btree_csum_one_bio() implemented this by memzeroing
the extent buffer's own folios before submission.
That destroys the in-memory buffer while it may still be referenced. In
particular btrfs_free_tree_block() can run on it afterwards and reads
the header to add a delayed reference; once the header has been zeroed
it frees bytenr 0 and corrupts the exten
btrfs: qgroup: fix a wrong length calculation in qgroup_free_reserved_data()
In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix a wrong length calculation in qgroup_free_reserved_data()
In that function, we round down the start position and round up the
ending position.
But during the calculation of @len, we use "round_up(start + len,
sectorsize)", which is the rounded up end position, not the rounded up
length.
Which results a much larger length, and later we are still using
"start + len", which is completely incorrect.
Fix it by declaring a local @aligned_start and @aligned_len and use them
instead.
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
Bluetooth: virtio_bt: avoid OOB read of build info string
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: virtio_bt: avoid OOB read of build info string
The virtbt_setup_zephyr() sends the Zephyr vendor command 0xfc08 (Read
Build Information) and hands the response to bt_dev_info() and
hci_set_fw_info() as a "%s" string starting at skb->data + 1, without
checking the length. A backend that answers with status only leaves that
pointer past the end of the received data, so the walk reads adjacent
slab memory until it meets a NUL. Those bytes reach the kernel log and
the firmware-info debugfs file.
To fix this, print the string with a bounded "%.*s" limited to
skb->len
Bluetooth: L2CAP: use proto_lock for l2cap_data to fix l2cap_disconn_ind
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: use proto_lock for l2cap_data to fix l2cap_disconn_ind
hci_conn::l2cap_data is accessed without locks in l2cap_disconn_ind via
hci_conn_timeout (disc_work) -> hci_proto_disconn_ind ->
l2cap_disconn_ind. This is UAF if the l2cap_conn is deleted
concurrently.
disc_work is disabled sync in hci_conn_del(), so we cannot take
hci_dev_lock in disc_work.
Fix by using proto_lock to guard l2cap_data, in addition to hdev->lock
which is held in other access paths.
Bluetooth: hci_conn: fix the SCO setup context lifetime
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: fix the SCO setup context lifetime
hci_setup_sync() queues a conn_handle_t with a NULL destroy callback, so
the context is only freed if hci_enhanced_setup_sync() actually runs. An
entry that is cancelled instead is leaked, as
_hci_cmd_sync_cancel_entry() does not release entry->data when there is
no destroy callback, and hci_cmd_sync_clear() cancels every pending entry
when the controller is unregistered.
The context also stores a bare hci_conn pointer, so the connection can be
freed while the work is queued. The dequeue in hci_conn_del() does not
cov
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
Bluetooth: hci_sync: free the advertising instance on the failure and cancel paths
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: free the advertising instance on the failure and cancel paths
adv_timeout_expire() hands a kmalloc()ed instance byte to
hci_cmd_sync_queue() with a NULL destroy callback, and only
adv_timeout_expire_sync() frees it. That leaks on two paths:
- the return value is not checked, and hci_cmd_sync_queue() does not
take ownership when it fails (-ENETDOWN, -ENODEV, -ENOMEM);
- a cancelled entry is not released, as _hci_cmd_sync_cancel_entry()
does not free entry->data when there is no destroy callback.
hci_cmd_sync_clear() cancels every pending ent
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
Bluetooth: MGMT: free the mesh send cancel command when it is cancelled
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: free the mesh send cancel command when it is cancelled
mesh_send_cancel() queues the pending command with a NULL destroy
callback, so it is only freed if send_cancel() runs. A cancelled entry is
leaked, as _hci_cmd_sync_cancel_entry() does not release entry->data when
there is no destroy callback, and hci_cmd_sync_clear() cancels every
pending entry when the controller is unregistered. Nothing else reclaims
it either: mgmt_pending_new() does not put the command on
hdev->mgmt_pending.
The leak also pins the socket reference taken by mgmt_pending_new(), so
t
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
Bluetooth: MSFT: validate evt_prefix_len against the response length
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MSFT: validate evt_prefix_len against the response length
read_supported_features() only checks that the response covers the fixed
part of struct msft_rp_read_supported_features, which is 11 bytes:
if (skb->len < sizeof(*rp)) {
bt_dev_err(hdev, "MSFT supported features length mismatch");
goto failed;
}
evt_prefix[] is a flexible array member and rp->evt_prefix_len is an
unvalidated u8 taken straight out of that response, so
msft->evt_prefix = kmemdup(rp->evt_prefix, rp->evt_prefix_len,
GFP_KERNEL);
copies up to 255 bytes from a reply that may ha