Sicherheitslücken in linux · Seite 173

net/mlx5e: Use sender devcom for MPV master-up

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Use sender devcom for MPV master-up After PCIe DPC recovery, mlx5 reloads the affected functions and replays multiport affiliation events. In the reported failure, the first relevant device error was: pcieport 0000:10:01.1: DPC: containment event pcieport 0000:10:01.1: PCIe Bus Error: severity=Uncorrected (Fatal) pcieport 0000:10:01.1: [ 5] SDES (First) mlx5 recovered the PCI functions and resumed 0000:11:00.1. During that resume, RDMA multiport binding replayed MLX5_DRIVER_EVENT_AFFILIATION_DONE and mlx5e sent MPV_DEVCOM_MASTER_UP. T

• Auf 6.8.0-147.147 aktualisieren

net/sched: serialize qdisc_rtab_list against concurrent get/put

In the Linux kernel, the following vulnerability has been resolved: net/sched: serialize qdisc_rtab_list against concurrent get/put qdisc_get_rtab() and qdisc_put_rtab() mutate the process-global singly linked list qdisc_rtab_list and a plain non-atomic 'int refcnt' with no lock. This was only safe because every caller historically held the RTNL mutex, which serialized all rate-table lookups, inserts and frees. That invariant no longer holds. cls_flower sets TCF_PROTO_OPS_DOIT_UNLOCKED, so tc_new_tfilter() keeps rtnl_held == false for it and sets TCA_ACT_FLAGS_NO_RTNL. That flag propagates through tcf_exts_validate_ex() -> tcf_action_init(

net/x25: fix use-after-free in x25_kill_by_neigh()

In the Linux kernel, the following vulnerability has been resolved: net/x25: fix use-after-free in x25_kill_by_neigh() x25_kill_by_neigh() walks the global X.25 socket list looking for sockets attached to a terminating neighbour. x25_list_lock protects list membership while the lookup is in progress, but it does not pin a socket's lifetime after the lock is dropped. The function currently drops x25_list_lock before calling lock_sock(s). A concurrent close can run x25_release(), remove the same socket from x25_list, and drop the last socket reference in that window. The neighbour teardown path can then lock or inspect a freed struct sock/st

• Auf 6.8.0-147.147 aktualisieren

net: gro: fix double aggregation of flush-marked skbs

In the Linux kernel, the following vulnerability has been resolved: net: gro: fix double aggregation of flush-marked skbs Commit 0ab03f353d36 ("net-gro: Fix GRO flush when receiving a GSO packet.") added a flush check to skb_gro_receive(), but skb_gro_receive_list() lacks the same validation. As a result, packets marked with NAPI_GRO_CB(skb)->flush may still be re-aggregated. This allows already-GRO'd packets with existing frag_list to be re-aggregated into a new GRO session, corrupting the frag_list chain structure. When skb_segment() attempts to unpack these malformed packets, it encounters invalid state and triggers a kernel panic. Sc

• Auf 6.8.0-147.147 aktualisieren

net: hip04: fix RX buffer leak on build_skb failure

In the Linux kernel, the following vulnerability has been resolved: net: hip04: fix RX buffer leak on build_skb failure When build_skb() fails in hip04_rx_poll(), the driver jumps to the refill path without releasing the current RX buffer and its DMA mapping. Installing a replacement buffer then overwrites the slot references and leaks both resources. Keep the current slot intact and return budget so NAPI retries the same buffer. Also free a newly allocated RX fragment when dma_map_single() fails. This issue was found by an in-house static analysis tool.

• Auf 6.8.0-147.147 aktualisieren

super: fix emergency thaw deadlock on frozen block devices

In the Linux kernel, the following vulnerability has been resolved: super: fix emergency thaw deadlock on frozen block devices do_thaw_all_callback() calls bdev_thaw() while holding sb->s_umount exclusively. If the block device was frozen via bdev_freeze() dropping the last block layer freeze reference calls fs_bdev_thaw() which reacquires s_umount: do_thaw_all_callback(sb) super_lock_excl(sb) # holds sb->s_umount bdev_thaw(sb->s_bdev) mutex_lock(&bdev->bd_fsfreeze_mutex) # bd_fsfreeze_count drops 1 -> 0 bd_holder_ops->thaw == fs_bdev_thaw get_bdev_super(bdev) bdev_super_loc

rbd: Reset positive result codes to zero in object map update path

In the Linux kernel, the following vulnerability has been resolved: rbd: Reset positive result codes to zero in object map update path In a reply message to an RBD request, a positive result code indicates a data payload, which is not allowed for writes. While rbd_osd_req_callback() already resets a positive result code for writes to zero, rbd_object_map_callback() does not. This allows a corrupted reply to an object map update to trigger the rbd_assert(*result < 0) in __rbd_obj_handle_request(). This happens, because rbd_object_map_callback() calls rbd_obj_handle_request() -> __rbd_obj_handle_request() and passes this positive result code.

• Auf 6.8.0-147.147 aktualisieren

ksmbd: defer destroy_previous_session() until after NTLM authentication

In the Linux kernel, the following vulnerability has been resolved: ksmbd: defer destroy_previous_session() until after NTLM authentication In ntlm_authenticate(), destroy_previous_session() is called using a user pointer resolved from the client-supplied NTLM blob username field before the NTLMv2 response is validated. An authenticated attacker can set the NTLM blob username to match a victim account and set PreviousSessionId to the victim's session ID; destroy_previous_session() destroys the victim's session while ksmbd_decode_ntlmssp_auth_blob() subsequently rejects the request with -EPERM. Move destroy_previous_session() and the prev_i

• Auf 6.8.0-147.147 aktualisieren

gve: fix Rx queue stall on alloc failure

In the Linux kernel, the following vulnerability has been resolved: gve: fix Rx queue stall on alloc failure When the system is under extreme memory pressure, page allocations can fail during the Rx buffer refill loop. If the number of buffers posted to hardware falls below a critical low threshold and the refill loop exits due to allocation failures, the queue can stall: 1. The device drops incoming packets because there are no descriptors. 2. Since no packets are processed, no Rx completions are generated. 3. Because no completions occur, NAPI is never scheduled, preventing the refill loop from running again even after memory is freed

• Auf 6.8.0-147.147 aktualisieren

ila: reload IPv6 header after pskb_may_pull in checksum adjust

In the Linux kernel, the following vulnerability has been resolved: ila: reload IPv6 header after pskb_may_pull in checksum adjust ila_csum_adjust_transport() caches ip6h = ipv6_hdr(skb) before calling pskb_may_pull(). On a non-linear skb whose transport header sits in a page fragment, pskb_may_pull() can call __pskb_pull_tail() / pskb_expand_head() and free the old skb head, leaving ip6h dangling; the following get_csum_diff(ip6h, p) then reads freed memory. ila_update_ipv6_locator() uses ip6h (and the iaddr derived from it) again after the csum-adjust call and additionally writes the new locator through that pointer. Impact: a remote IPv

• Auf 6.8.0-147.147 aktualisieren

mac802154: hold an interface reference across the scan worker

In the Linux kernel, the following vulnerability has been resolved: mac802154: hold an interface reference across the scan worker mac802154_scan_worker() captures the scanning sub-interface under RCU and then keeps dereferencing sdata->dev after rcu_read_unlock() and outside the rtnl -- in the failure traces, in mac802154_transmit_beacon_req() (skb->dev = sdata->dev), and in the end_scan cleanup. Nothing keeps that netdev alive across the worker iteration. A concurrent DEL_INTERFACE or PHY removal can unregister the interface once the worker drops the rtnl between its two drv_set_channel() sections. unregister_netdevice() frees the netdev

• Auf 6.8.0-147.147 aktualisieren

mac802154: llsec: reject frames shorter than the authentication tag

In the Linux kernel, the following vulnerability has been resolved: mac802154: llsec: reject frames shorter than the authentication tag llsec_do_decrypt_auth() computes the associated-data length for the AEAD request as assoclen += datalen - authlen; where datalen is the number of bytes after the MAC header and authlen (4, 8 or 16) is the length of the authentication tag. Nothing verifies that the frame actually carries at least authlen payload bytes. A secured frame whose payload is shorter than the tag makes datalen - authlen negative; assoclen is then passed to aead_request_set_ad() as an unsigned value close to 4 GiB, so crypto_aead_

• Auf 6.8.0-147.147 aktualisieren

mctp: serial: handle zero-length frames to prevent rx buffer overflow

In the Linux kernel, the following vulnerability has been resolved: mctp: serial: handle zero-length frames to prevent rx buffer overflow The MCTP serial receive state machine reads a frame length byte in mctp_serial_push_header() case 2 and validates it upper-bound-only: if (c > MCTP_SERIAL_FRAME_MTU) { dev->rxstate = STATE_ERR; } else { dev->rxlen = c; dev->rxpos = 0; dev->rxstate = STATE_DATA; ... } A length of zero passes this check, so rxlen is set to 0 and the state machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the incoming byte is stored and rxpos incremented before the terminator is dev->rxbuf[de

• Auf 6.8.0-147.147 aktualisieren

openvswitch: fix GSO userspace truncation underflow

In the Linux kernel, the following vulnerability has been resolved: openvswitch: fix GSO userspace truncation underflow OVS_ACTION_ATTR_TRUNC currently stores a delta from the original skb length in OVS_CB(skb)->cutlen. When a later userspace action segments a GSO skb, queue_gso_packets() reuses that delta for each smaller segment. A segment can then reach queue_userspace_packet() with cutlen greater than skb->len, underflowing the length passed to skb_zerocopy(). Store the maximum preserved length instead and bound each consumer against the current skb length. Use U32_MAX as the no-truncation sentinel so the value remains valid if skb geo

• Auf 6.8.0-147.147 aktualisieren

pppoe: reload header pointer after dev_hard_header()

In the Linux kernel, the following vulnerability has been resolved: pppoe: reload header pointer after dev_hard_header() pppoe_sendmsg() saves a pointer to the PPPoE header before calling dev_hard_header(). Device header callbacks are allowed to reallocate the skb head, invalidating pointers into it. This can happen when a send is blocked in copy_from_user() while the first non-Ethernet port is added to an empty team device. The team's delegated GRE header callback then expands the skb head. PPPoE subsequently writes six bytes through the stale pointer into the freed head. Reload the PPPoE header through the skb's network-header offset af

• Auf 6.8.0-147.147 aktualisieren

tcp: initialize standalone TCP-AO response padding

In the Linux kernel, the following vulnerability has been resolved: tcp: initialize standalone TCP-AO response padding tcp_v4_send_ack() and tcp_v6_send_response() construct standalone TCP responses with TCP-AO options. The option length carries the actual MAC length, but the TCP header length includes the option rounded up to a four-byte boundary. tcp_ao_hash_hdr() writes the MAC only. Thus, when the MAC length is not four-byte aligned, the one to three bytes after the MAC are left uninitialized and may be transmitted. For the normal TCP-AO hashing mode, those bytes also have to be initialized before computing the MAC. Initialize only

• Auf 6.8.0-147.147 aktualisieren

tcp: challenge ACK for non-exact RST in SYN-RECEIVED

In the Linux kernel, the following vulnerability has been resolved: tcp: challenge ACK for non-exact RST in SYN-RECEIVED The SYN-RECEIVED request-socket path in tcp_check_req() accepts an in-window RST without requiring SEG.SEQ to exactly match RCV.NXT. A non-exact RST therefore removes the request instead of eliciting a challenge ACK. RFC 9293 section 3.10.7.4 applies the RFC 5961 reset check in SYN-RECEIVED: an exact RST resets the connection, while a non-exact in-window RST must trigger a challenge ACK and be dropped. Apply that check before the ACK-field validation, following the RFC sequence-number, RST, then ACK processing order.

tipc: clear sock->sk on the failed-insert path in tipc_sk_create()

In the Linux kernel, the following vulnerability has been resolved: tipc: clear sock->sk on the failed-insert path in tipc_sk_create() When tipc_sk_create() fails to insert the new socket (tipc_sk_insert() returns non-zero), its error path frees the sk with sk_free() but leaves sock->sk pointing at the freed object: if (tipc_sk_insert(tsk)) { sk_free(sk); pr_warn("Socket create failed; port number exhausted\n"); return -EINVAL; } This is harmless for plain socket(): the syscall layer clears sock->ops before releasing, so tipc_release() is never called. It is not harmless on the accept() path. tipc_accept() creates the pre-allocate

• Auf 6.8.0-147.147 aktualisieren

vxlan: mdb: Fix source list corruption on a failed replace

In the Linux kernel, the following vulnerability has been resolved: vxlan: mdb: Fix source list corruption on a failed replace When replacing the source list of an MDB remote entry, all existing sources are first marked for deletion and vxlan_mdb_remote_srcs_add() is then called to add the new source list. Sources present in the new list have their deletion mark cleared, and any sources left marked afterwards are removed. If vxlan_mdb_remote_srcs_add() fails partway through, its error path deletes all entries on the remote's source list. That rollback is only correct for its other caller, vxlan_mdb_remote_add(), where the remote was just a

• Auf 6.8.0-147.147 aktualisieren

drm/amdgpu/gfx10: replace BUG_ON() with WARN_ON()

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/gfx10: replace BUG_ON() with WARN_ON() There's no need to crash the kernel for these cases. (cherry picked from commit ac6f00beb658239bced4aaed9efbb04a35348d48)

• Auf 6.8.0-147.147 aktualisieren