In the Linux kernel, the following vulnerability has been resolved:
USB: gadget: ffs: fix mm lifetime handling
io_data stores a pointer to the submitting task's mm_struct,
but does not currently hold a reference to it while async
requests are pending.
This can result in a use-after-free if the task exits before
completion handling finishes.
Take a reference with mmgrab() when queuing the read request
and release it with mmdrop() on request completion.
usb: gadget: f_fs: Fix Use-After-Free in AIO error path
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_fs: Fix Use-After-Free in AIO error path
In ffs_epfile_write_iter() and ffs_epfile_read_iter(), when ffs_epfile_io()
fails with an error other than -EIOCBQUEUED, the io_data structure (`p`) is
freed. However, for AIO operations, the kiocb cancel function was already
armed and kiocb->private was set to `p`.
If a concurrent cancel operation (such as sys_io_cancel()) executes after
ffs_epfile_io() fails but before the function frees `p`, a Use-After-Free
can occur when the cancellation handler accesses the freed pointer.
To securely fix this race condition, we
ceph: properly decrypt filenames in vmalloc() buffers
In the Linux kernel, the following vulnerability has been resolved:
ceph: properly decrypt filenames in vmalloc() buffers
The fscrypt subsystem uses the scatterlist crypto API, inheriting its
requirement that any buffers are in the linear mapping region. However,
the messenger client uses kvmalloc() to create buffers for messages,
which will occasionally place those buffers in the vmalloc() region when
physical memory fragmentation doesn't permit a large enough kmalloc().
The various callers of ceph_fname_to_usr() directly pass (slices of) raw
messages from the MDS without considering that the messages may be in
vmalloc() buffers, resulting
In the Linux kernel, the following vulnerability has been resolved:
HID: sony: clean up device list on probe failure
sony_input_configured() adds some controllers to sony_device_list before
HID core registers their input devices. input_register_device() can fail
after the callback returns successfully. sony_probe() then observes that
HID_CLAIMED_INPUT is clear and unwinds, but only stops the HID hardware.
The devres-managed sony_sc is freed while its list node remains linked, so
the next matching controller traverses freed memory.
Initialize the list node and device ID to inactive states. Make list
removal idempotent and run the driver-pri
NFSD: Prevent client use-after-free during close_lru reaping
In the Linux kernel, the following vulnerability has been resolved:
NFSD: Prevent client use-after-free during close_lru reaping
An nfs4_openowner left on nn->close_lru after its final CLOSE keeps
its last closed stateid in oo_last_closed_stid, holding only a raw
pointer to its nfs4_client. The laundromat reaps timed-out entries,
drops nn->client_lock, and calls nfs4_put_stid(), which dereferences
the client through cl_lock. Nothing pins the client across that
window, so a concurrent force_expire_client() can free it and
nfs4_put_stid() reads freed memory. __destroy_client() hits the same
race, walking clp->cl_openowners without cl_lock.
P
NFSD: Prevent client use-after-free during blocked-lock reaping
In the Linux kernel, the following vulnerability has been resolved:
NFSD: Prevent client use-after-free during blocked-lock reaping
A bare lock owner -- its only remaining reference a blocked lock on
nn->blocked_locks_lru -- holds a raw pointer to its nfs4_client but
no reference keeping the client alive. When the per-net laundromat
reaps such a lock, freeing the nbl drops the owner reference
held through flc_owner, and the final nfs4_put_stateowner()
takes the client's cl_lock. Because the laundromat detaches the
nbl first, __destroy_client() no longer finds it, so a concurrent
force_expire_client() can free the client before nfs4_put_stat
Nicht bewertetEPSS 0,19%Keine Korrektur veröffentlicht
drm/amd/display: fix division by zero in get_estimated_bw()
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: fix division by zero in get_estimated_bw()
get_estimated_bw() divides by link->dpia_bw_alloc_config.bw_granularity,
which is zeroed by reset_bw_alloc_struct() and only populated once
DP_TUNNELING_BW_ALLOC_CAP_CHANGED has been handled.
link_dp_dpia_handle_bw_alloc_status(), the DPCD interrupt handler,
calls get_estimated_bw() whenever DP_TUNNELING_ESTIMATED_BW_CHANGED
is set, independently of whether DP_TUNNELING_BW_ALLOC_CAP_CHANGED
has ever fired for that link. A connected USB4/DPIA tunneling device
that reports an estimated-bandwidth change before ever r
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
usb: image: mdc800: change kmalloc() to kzalloc()
In the Linux kernel, the following vulnerability has been resolved:
usb: image: mdc800: change kmalloc() to kzalloc()
Change the kmalloc() calls in usb_mdc800_init() for irq_urb_buffer and
download_urb_buffer to kzalloc(), avoiding potential stack leaks if a
shorter message is received in mdc800_usb_irq() and
mdc800_usb_download_notify()
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
ALSA: usb-audio: fix OOB write in snd_usbmidi_us122l_output()
In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: fix OOB write in snd_usbmidi_us122l_output()
The snd_usbmidi_us122l_output() picks a count of 2 on anything slower
than high speed and never relates it to ep->max_transfer. The URB
buffer holds exactly max_transfer bytes, so a device declaring a one
byte bulk endpoint takes two bytes from snd_rawmidi_transmit(), and the
memset that pads the rest computes 1 - 2 in int and wraps to SIZE_MAX.
Only 0x800e and 0x800f are pinned to nine bytes. The US-122MKII at
0x0644:0x8021 falls to the default and takes usb_maxpacket(), which the
USB core only clamps downwar
media: usbtv: keep device alive while ALSA card exists
In the Linux kernel, the following vulnerability has been resolved:
media: usbtv: keep device alive while ALSA card exists
The ALSA PCM callbacks store the driver state in pcm->private_data. An
open PCM file can outlive USB disconnect because usbtv_audio_free() uses
snd_card_free_when_closed(). The disconnect path can then drop the V4L2
device reference and free struct usbtv before ALSA releases the substream,
so a later close dereferences freed memory in snd_usbtv_pcm_close().
Take a V4L2 device reference for the ALSA card and drop it from the card
private_free callback. This keeps struct usbtv valid until ALSA has closed
the remaining fi
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
usb-storage: ene_ub6250: fix race between scan work and probe
In the Linux kernel, the following vulnerability has been resolved:
usb-storage: ene_ub6250: fix race between scan work and probe
ene_ub6250_probe() calls usb_stor_probe2(), which starts the usb-storage
infrastructure and schedules the delayed scan work. The driver then
calls ene_get_card_type(), which sends an ENE command through
ene_send_scsi_cmd() and the usb-storage bulk transfer helpers.
Both the delayed scan work, through usb_stor_Bulk_max_lun(), and
ene_get_card_type() use us->current_urb. The scan work serializes this
access with us->dev_mutex, but the ENE card-type probe does not. If the
scan work runs while ene_get_card_type()
In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: clear forceRM when issuing EndTransfer
The forceRM bit of the DEPCMD register controls the behavior of the
EndTransfer command used to stop an active transfer. Older DWC3
programming guide revisions recommended setting forceRM=1 when
issuing EndTransfer. Newer programming guide revisions recommend
issuing EndTransfer with forceRM cleared.
With forceRM=1 on DWC_usb31 v2.00a and v2.10a controllers, a transfer
aborted through the ep_dequeue path was observed to remain active
after EndTransfer completion. A subsequent StartTransfer issued on the
same endpoint trigge
usb: storage: realtek_cr: fix use-after-free on disconnect
In the Linux kernel, the following vulnerability has been resolved:
usb: storage: realtek_cr: fix use-after-free on disconnect
realtek_cr_destructor() calls timer_delete() before the chip containing
the timer is freed. The timer callback may still be running and can
rearm itself, resulting in a use-after-free.
Use timer_shutdown_sync() to wait for the callback and prevent further
rearming. Do this unconditionally because ss_en may be changed after
the timer is armed.
Move timer_setup() into init_realtek_cr() so the timer is initialized
before any failure path can invoke the destructor.
Found by static analysis.
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic-typec: disable cc_debounce_dwork on stop
cc_debounce_dwork is queued from the set_cc() and start_toggling()
callbacks, which run from TCPM's kthread worker. port_stop() returns
before tcpm_unregister_port() destroys that worker. Flushing the worker
during unregister may therefore run a callback which queues the delayed
work after port_stop() has returned.
The delayed work can then run after devres has freed pmic_typec_port.
Use disable_delayed_work_sync() in port_stop() to cancel a pending
instance and prevent the TCPM callbacks from queueing anoth
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: qcom-pmic: cancel reset_work on stop
pdphy_stop() disables IRQs but leaves reset_work pending. If the IRQ
handler schedules it just before disable_irq(), the work runs after
remove() frees the struct via devm.
Call cancel_work_sync() after disabling IRQs to close the window.
This issue was found by an in-house static analysis tool.
usb: typec: ucsi: displayport: Fix OOB altmode array index
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: displayport: Fix OOB altmode array index
The UCSI displayport driver indexes the connector's port altmode array
with the GET_CURRENT_CAM response after checking it is not 0xff. The
port altmode array is UCSI_MAX_ALTMODES elements long. If the PPM
returns an invalid GET_CURRENT_CAM response above UCSI_MAX_ALTMODES and
not equal to 0xff, the kernel may crash with an array index OOB error.
Update the UCSI displayport driver to verify the current cam is less
than UCSI_MAX_ALTMODES before accessing the port altmode array.
Nicht bewertetEPSS 0,2%Keine Korrektur veröffentlicht
usb: gadget: midi2: Fix null-pointer dereference in f_midi2_free_ep_reqs
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: midi2: Fix null-pointer dereference in f_midi2_free_ep_reqs
A null-pointer dereference occurs in f_midi2_free_ep_reqs() when attempting
to clean up an endpoint that was never initialized.
When configuring the MIDI 2.0 gadget via configfs and setting the block
direction to SNDRV_UMP_DIR_INPUT, the initialization of the midi1_ep_out
endpoint is explicitly skipped during the gadget bind phase
(f_midi2_bind()). As a result, the usb_ep->card field remains NULL.
Later, when the host sets the alternate setting, f_midi2_set_alt()
unconditionally stops both the IN and
Nicht bewertetEPSS 0,23%Keine Korrektur veröffentlicht
usb: gadget: f_mass_storage: fix null pointer dereference in fsg_common_set_num_buffers()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_mass_storage: fix null pointer dereference in fsg_common_set_num_buffers()
Previously fsg_num_buffers_validate() was removed as it was not
necessary due to Kconfig setting the limits for n from 2 to 256 with
default as 2. However, setting the page content in such a way that
kstrtou8() reflects n value as either 0 or 1 bypasses these
restrictions leading to a null pointer dereference if n is 0. Fix
this by adding a check for n < 2 and returning -EINVAL if n is
either 0 or 1 consistent with Kconfig logic.
usb: gadget: f_midi2: fix use-after-free in string attribute show path
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi2: fix use-after-free in string attribute show path
f_midi2_opts_str_show() takes the string lock internally, but its
callers dereference the opts->info.<field> pointer before calling it,
outside the lock. This races with f_midi2_opts_str_store(), which
frees the old string under opts->lock when the attribute is written
concurrently, the show path can read a pointer that gets freed
before the lock inside str_show() is even taken.
Change f_midi2_opts_str_show() to take a pointer to the string field,
matching the existing pattern in f_midi2_opts_str_store(
Nicht bewertetEPSS 0,21%Keine Korrektur veröffentlicht
usb: gadget: f_midi: initialize work in f_midi_alloc()
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi: initialize work in f_midi_alloc()
f_midi_alloc initializes free_ref to 1 and it can only be incremented
when a sound card is registered via f_midi_register_card().
f_midi_register_card() is only called in f_midi_bind() which actually
performs INIT_WORK. If f_midi_bind() is never run, work is not
initialized and the if condition in f_midi_free becomes true,
this results in a warning later in __flush_work as work->func = 0.
Fix this by moving INIT_WORK from f_midi_bind() to f_midi_alloc().