Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
USB: dwc2: shut down wakeup timer before freeing HCD state
In the Linux kernel, the following vulnerability has been resolved:
USB: dwc2: shut down wakeup timer before freeing HCD state
dwc2_wakeup_detected() accesses the DWC2 host state and can rearm the
wakeup timer. dwc2_hcd_free() currently deletes the timer only after
freeing host-owned state, and timer_delete() does not synchronize a
callback or prevent it from being queued again.
Stop and shut down the timer in dwc2_hcd_release(), before the HCD
resources are freed. This covers both the HCD initialization error path
and normal HCD removal.
usb: typec: tcpm: recover after failure to start the frs ams
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: recover after failure to start the frs ams
Reset the port if the tcpm fails to start the FAST_ROLE_SWAP AMS by
initiating error recovery on it.
This helps in cases where some cables (incorrectly) signal an FRS to
an FRS capable port during disconnection. The TCPC autonomously starts
sourcing VBUS on detecting the FRS signal. However, the VBUS sourcing is
left on when the FAST_ROLE_SWAP AMS fails to start (as tcpm_sink_tx_ok
is 0 as CC is open due to the cable disconnect). This is because the
code sets the state to INVALID_STATE without resetting the port
usb: typec: tipd: fix uninitialized typec_partner_desc in tps6598x_connect()
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tipd: fix uninitialized typec_partner_desc in tps6598x_connect()
tps6598x_connect() passes a stack-allocated typec_partner_desc to
typec_register_partner() after initializing only usb_pd, accessory and
identity.
typec_register_partner() copies attach and deattach from the descriptor
into the partner. With those fields left unset, garbage function pointers
may be stored and later invoked from typec_partner_link_device() when a USB
device is linked to the port. Uninitialized pd_revision and usb_capability
similarly leak stack data through partner sysfs.
Zero-ini
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
usb: cdns3: fix use-after-free in cdns3_gadget_exit()
In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: fix use-after-free in cdns3_gadget_exit()
cdns3_gadget_start() arms two works on system_freezable_wq:
pending_status_wq for the deferred ep0 status stage and aligned_buf_wq
for realigned request buffers. Both handlers use the cdns3_device the
works are embedded in, and cdns3_pending_setup_status_handler() also
calls the ep0 request completion.
cdns3_gadget_exit() does not wait for these works. It frees all
endpoints and aligned buffers and drops the last reference to the
gadget device, which frees priv_dev, so a work queued before the exit
can run after the fre
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
usb: cdns3: Fix NULL pointer dereference in cdns3_pci_probe
In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: Fix NULL pointer dereference in cdns3_pci_probe
The Cadence USBSS controller is a two-function PCI device. The first
probed function allocates the driver data and stores it with
pci_set_drvdata(), while the second function reuses it via
pci_get_drvdata() when pci_is_enabled() reports that the first
function has already been probed.
When the second function is probed while the first one has been
enabled but has not yet set its driver data, pci_get_drvdata()
returns NULL, and the subsequent wrap->devfn assignment dereferences
a NULL pointer and crashes the kernel
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
tty: vcc: zero-initialize control packet in vcc_send_ctl()
In the Linux kernel, the following vulnerability has been resolved:
tty: vcc: zero-initialize control packet in vcc_send_ctl()
The stack-allocated struct vio_vcc pkt was partially initialized,
leaving the tag.stype_env field uninitialized before being sent via
ldc_write(), potentially leaking kernel stack data to the LDC peer.
tty: vcc: hold port lock when clearing tty pointer in vcc_cleanup
In the Linux kernel, the following vulnerability has been resolved:
tty: vcc: hold port lock when clearing tty pointer in vcc_cleanup
vcc_cleanup() sets port->tty to NULL without holding port->lock, racing
with vcc_event() LDC callbacks that read port->tty under port->lock and
then use tty->port. This can cause a use-after-free when the callback
dereferences tty->port after cleanup has already destroyed and freed it.
tty: tty_port: restore TTY_IO_ERROR on activation failure
In the Linux kernel, the following vulnerability has been resolved:
tty: tty_port: restore TTY_IO_ERROR on activation failure
Make sure to restore the TTY_IO_ERROR flag if activation fails to
prevent I/O attempts on a port that is gone or powered down.
This specifically avoids issues like kernel panic due to unclocked
accesses or NULL-pointer dereferences when accessing powered down or
deregistered ports when a TTY ioctl races with hangup and open.
Note that the flag is set again in tty_port_close() but not restoring it
on activation failure leaves a window where drivers fail to handle the
ioctl-hangup race.
In the Linux kernel, the following vulnerability has been resolved:
tty: port: fix tty_port_tty_vhangup() race
Drivers rely on tty_port_tty_vhangup() to synchronously hang up their
ports before tearing down resources as part of deregistration (e.g. on
physical disconnect).
If tty_port_tty_vhangup() races with another hangup it may however
return before the port has been shut down. This is in turn can lead to
use-after-free and NULL-pointer dereferences in racing ioctls (including
a synchronous hangup) and in processing of racing asynchronous hangups
(carrier loss).
Add the missing serialisation to tty_port_tty_vhangup() and
tty_port_hangu
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
tty: abort break signalling on hangup
In the Linux kernel, the following vulnerability has been resolved:
tty: abort break signalling on hangup
The break ioctls can race with hangup and end up calling into a tty
driver for a device that is already gone or powered down.
Drivers must handle this race, but TCSBRK and TCSBRKP should still be
aborted to avoid calling back into the driver after a user-controlled
timeout (possibly even after the tty has been reopened).
Note that drivers should disable any break state on shutdown so just
return on hangup (calling break_ctl() again is racy and will most likely
fail for drivers handling the race).
In the Linux kernel, the following vulnerability has been resolved:
tty: fix saved termios reset race
Resetting saved termios state on device registration is needed where a
minor number can be reused for an entirely different device and where
the old settings may prevent the port from even being opened (e.g. when
CLOCAL is not set).
Not all TTY drivers guarantee that the minor number is no longer in use
when registering devices however, something which can lead to a
use-after-free when closing a TTY (and saving its termios) races with
re-registration.
Add a new TTY_DRIVER_RESET_SAVED_TERMIOS flag to request that any saved
termios state is
Nicht bewertetEPSS 0,18%Keine Korrektur veröffentlicht
tty: serial: max3100: shut down timer before freeing port
In the Linux kernel, the following vulnerability has been resolved:
tty: serial: max3100: shut down timer before freeing port
max3100_shutdown() stops the polling timer but returns early during
system suspend. If the SPI device is unbound before resume, the serial
core does not call max3100_shutdown() again, so max3100_remove() frees
the port while the timer remains armed. max3100_timeout() may then
access the freed port and re-arm the timer.
Add final timer teardown to max3100_remove() and use
timer_shutdown_sync() to prevent a racing callback from re-arming it.
Also free the IRQ and destroy the workqueue there before freeing the
port. Ke
Nicht bewertetEPSS 0,17%Keine Korrektur veröffentlicht
serial: 8250_bcm7271: fix use-after-free in brcmuart_remove()
In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_bcm7271: fix use-after-free in brcmuart_remove()
brcmuart_handle_irq() starts priv->hrt to work around a receive-timeout
quirk of the 8250 core when hardware flow control is enabled; the timer
callback brcmuart_hrtimer_func() dereferences priv.
brcmuart_remove() cancels the hrtimer before it unregisters the port, so
a receive-timeout interrupt that arrives in between re-arms the timer.
After devm frees priv, the callback runs on freed memory.
Unregister the port before cancelling the hrtimer.
serial8250_unregister_port() shuts the port down and frees its IRQ,
arm64/fpsimd: signal: Forbid non-streaming SVE payload on SME-only systems
In the Linux kernel, the following vulnerability has been resolved:
arm64/fpsimd: signal: Forbid non-streaming SVE payload on SME-only systems
When system_supports_sme() is true but system_supports_sve() is false,
restoring a specifically crafted SVE signal context can result in the
task erroneously having non-streaming SVE state. Subsequent attempts to
manipulate the task's FPSIMD/SVE/SME state can result in a variety of
problems, including fatal EL1 UNDEFs.
In such configurations, the kernel always creates an SVE signal context
when delivering a signal, and this can only be in one of two states:
(1) SVE_SIG_FLAG_SM is set, and an SVE pa
In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize compat port-info ioctls
The native sequencer ioctl path serializes handler calls with
client->ioctl_mutex, but the translated port-info compat path invokes the
same handlers through snd_seq_kernel_client_ctl() without taking that
mutex.
This lets concurrent compat CREATE_PORT requests pass the port-count
check before any request reaches the serialized insertion. The computed
integer port index can then exceed the address field range and wrap to an
existing index. Subsequent subscriber teardown can resolve the duplicate
address to the wrong port and acc
In the Linux kernel, the following vulnerability has been resolved:
ALSA: ua101: reject mismatched capture/playback packet sizes
detect_usb_format() cross-checks bSubframeSize, bBitResolution and
tSamFreq between the capture and playback interfaces, but never relates
the two endpoints' wMaxPacketSize and bNrChannels. Each playback URB
gets a buffer of ua->playback.max_packet_bytes, while the number of
bytes written into it is derived from the capture stream:
capture_urb_complete() computes frames from the received capture packet
and capture.frame_bytes, and start_usb_playback() and playback_work()
multiply that by playback.frame_bytes.
A
Nicht bewertetEPSS 0,18%Keine Korrektur veröffentlicht
EDAC/altera: Drop __init from ECC setup paths for re-probe safety
In the Linux kernel, the following vulnerability has been resolved:
EDAC/altera: Drop __init from ECC setup paths for re-probe safety
Sashiko reports:
"Does suppressing sysfs unbinding fully prevent the execution of freed __init
memory? If altr_sysmgr_regmap_lookup_by_phandle() returns -EPROBE_DEFER, the
probe is deferred until after __init memory is freed."
The a10 EDAC .setup callbacks (sdmmc, ethernet, nand, dma, usb, qspi) and
their helpers (altr_init_a10_ecc_device_type, altr_init_a10_ecc_block) were
marked __init. These run from the probe path, which may execute after init
memory is freed -- e.g. a probe deferred via -EPROBE_DEFER t
Bluetooth: RFCOMM: Fix initial port reference race
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix initial port reference race
For RFCOMM_RELEASE_ONHUP devices, rfcomm_tty_install() and
__rfcomm_release_dev() both use RFCOMM_TTY_OWNED to decide who drops the
initial tty_port reference. The release path tests the bit separately
from the install path setting it, so both can drop that reference.
The synchronous hangup does not prevent this race: port->tty is not
assigned until tty_port_open(), after installation. The following
interleaving is possible:
1. Install and release each obtain a reference with rfcomm_dev_get().
2. Release observes RFCO
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Serialize SMP remote OOB data access
build_pairing_cmd() looks up remote OOB data and copies its contents
without holding hdev->lock, which serializes the list's writers. After
SMP finds an entry, a concurrent management Remove Remote OOB Data
command can unlink and free it before SMP reads its present flag or
copies its random and confirmation values. Removal can also invalidate
an entry while the lookup is still traversing the list.
KASAN reported:
BUG: KASAN: slab-use-after-free in build_pairing_cmd+0x948/0x9b0
Call Trace:
build_pairing_cmd+0x948/0x9b
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix inquiry cache use-after-free
The sync command worker holds hdev->req_lock, but inquiry-cache updates
and flushes use hdev->lock. Both hci_acl_create_conn_sync() and
hci_stop_discovery_sync() look up entries and read their fields without
taking hdev->lock.
After either lookup returns, a concurrent HCIINQUIRY ioctl can acquire
hdev->lock and flush the cache, freeing the entry. The worker then reads
the freed entry while preparing a create-connection or remote-name-cancel
command. The list traversal also races with cache updates and removal.
KASAN re