KVM: arm64: nv: Inject SEA if kvm_translate_vncr() can't resolve PFN
In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: nv: Inject SEA if kvm_translate_vncr() can't resolve PFN
kvm_handle_vncr_abort() assumes that s1_walk_result conveys an abort
when kvm_translate_vncr() returns -EFAULT. This is not always the case
as it's possible to encounter 'late' failures on the output of S1
translation, e.g. a GFN outside of the memslots.
Fix it by preparing an external abort before returning from
kvm_translate_vncr(). Get rid of the BUG_ON() in the fault injection
path while at it.
In the Linux kernel, the following vulnerability has been resolved:
netfilter: xt_nat: reject unsupported target families
xt_nat SNAT and DNAT target handlers assume IP-family conntrack state
is present and can dereference a NULL pointer when instantiated from an
unsupported family through nft_compat. A bridge-family compat rule can
therefore trigger a NULL-dereference in nf_nat_setup_info().
Reject non-IP families in xt_nat_checkentry() so unsupported targets
cannot be installed. Keep NFPROTO_INET allowed for valid inet NAT
compat users and leave the runtime fast path unchanged.
[ The crash was fixed via
9dbba7e694ec ("netfilter: nft_c
tools/power/x86/intel-speed-select: Harden daemon pidfile open
In the Linux kernel, the following vulnerability has been resolved:
tools/power/x86/intel-speed-select: Harden daemon pidfile open
Avoid symlink-based pidfile clobbering by opening the pidfile with
O_NOFOLLOW and validating it with fstat() before locking/writing.
The daemon currently uses a fixed pidfile path under /tmp. A local
unprivileged user can pre-create a symlink at that path and cause a
root-run daemon instance to write into an attacker-chosen file.
cxl: Fix CXL_HEADERLOG_SIZE to match RAS Capability size
In the Linux kernel, the following vulnerability has been resolved:
cxl: Fix CXL_HEADERLOG_SIZE to match RAS Capability size
The CXL r4.0 8.2.4.17.7 RAS Capability Structure has total length 0x58
bytes (CXL_RAS_CAPABILITY_LENGTH); the Header Log occupies the trailing
64 bytes at offset 0x18. CXL_HEADERLOG_SIZE was defined as SZ_512,
eight times the actual on-device size.
header_log_copy() reads CXL_HEADERLOG_SIZE_U32 (128) dwords from the
RAS capability iomap, overrunning the 88-byte mapping by 448 bytes.
The cxl_aer_uncorrectable_error trace event memcpy()s CXL_HEADERLOG_SIZE
(512) bytes from its source. For the CPER caller the source i
ufs: core: tracing: Do not dereference pointers in TP_printk()
In the Linux kernel, the following vulnerability has been resolved:
ufs: core: tracing: Do not dereference pointers in TP_printk()
The trace events in drivers/ufs/core/ufs_trace.h were converted to take a
pointer to the hba structure as an argument for the tracepoint and then in
TP_printk() the printing of the dev_name from the ring buffer was
converted to using the dev dereferenced pointer from the hba saved
pointer.
This is not allowed as the TP_printk() is executed at the time the trace
event is read from /sys/kernel/tracing/trace file. That can happen
literally, seconds, minutes, hours, weeks, days, or even months later!
There is no gu
In the Linux kernel, the following vulnerability has been resolved:
hwmon: (occ) unregister sysfs devices outside occ lock
occ_active(false) and occ_shutdown() unregister sysfs-backed devices while
occ->lock is held. hwmon_device_unregister() and sysfs_remove_group() can
wait for active sysfs callbacks to drain, and those callbacks can enter the
OCC update path and try to take occ->lock again. That gives the unregister
paths the lock ordering occ->lock -> sysfs callback drain, while a callback
has the opposite edge sysfs callback -> occ->lock.
This issue was found by our static analysis tool and then manually
reviewed against the current
mmc: vub300: defer reset until cmd_mutex is unlocked
In the Linux kernel, the following vulnerability has been resolved:
mmc: vub300: defer reset until cmd_mutex is unlocked
vub300_cmndwork_thread() holds cmd_mutex while it sends a command and
waits for the command response. If the response wait times out,
__vub300_command_response() kills the command URBs and then synchronously
resets the USB device through usb_reset_device().
That reset path re-enters the driver through vub300_pre_reset(), which
also takes cmd_mutex. The worker therefore tries to acquire the same
mutex recursively while it is still holding it from the command path.
This issue was found by our static analysis tool and th
drm/rockchip: dw_dp: Fix null-ptr-deref in dw_dp_remove()
In the Linux kernel, the following vulnerability has been resolved:
drm/rockchip: dw_dp: Fix null-ptr-deref in dw_dp_remove()
Attempting to access driver data in the platform driver ->remove()
callback may lead to a null pointer dereference since there is no
guaranty that the component ->bind() callback invoking
platform_set_drvdata() was executed.
A common scenario is when Rockchip DRM driver didn't manage to run
component_bind_all() because of an (unrelated) error causing early
return from rockchip_drm_bind().
Drop the unnecessary call to platform_get_drvdata() and, instead,
reference the target device structure via platform_device.
accel/amdxdna: Guard management mailbox channel cleanup against NULL pointer
In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Guard management mailbox channel cleanup against NULL pointer
The management mailbox channel cleanup helpers can be called from
error handling paths when mgmt_chann has already been destroyed.
Add NULL checks to xdna_mailbox_free_channel() and
xdna_mailbox_stop_channel() so the cleanup path safely returns instead
of dereferencing a NULL mailbox channel pointer.
soc: xilinx: Fix race condition in event registration
In the Linux kernel, the following vulnerability has been resolved:
soc: xilinx: Fix race condition in event registration
The zynqmp_power driver registers handlers for suspend and subsystem
restart events using register_event(). However, the work structures
(zynqmp_pm_init_suspend_work and zynqmp_pm_init_restart_work) used by
these handlers were allocated and initialized after the registration
call.
This created a race window where, if the firmware triggered an event
immediately after registration but before allocation, the callback
(suspend_event_callback or subsystem_restart_event_callback) would
dereference a NULL pointer in work_pendi
In the Linux kernel, the following vulnerability has been resolved:
soc: xilinx: Shutdown and free rx mailbox channel
A mbox rx channel is requested using mbox_request_channel_byname() in
probe. In remove callback, the rx mailbox channel is cleaned up when the
rx_chan is NULL due to incorrect condition check. The mailbox channel is
not shutdown and it can receive messages even after the device removal.
This leads to use after free. Also the channel resources are not freed.
Fix this by checking the rx_chan correctly.
scsi: hisi_sas: Add slave_destroy interface for v3 hw
In the Linux kernel, the following vulnerability has been resolved:
scsi: hisi_sas: Add slave_destroy interface for v3 hw
WARNING is triggered when executing link reset of remote PHY and rmmod
SAS driver simultaneously. Following is the WARNING log:
WARNING: CPU: 61 PID: 21818 at drivers/base/core.c:1347 __device_links_no_driver+0xb4/0xc0
Call trace:
__device_links_no_driver+0xb4/0xc0
device_links_driver_cleanup+0xb0/0xfc
__device_release_driver+0x198/0x23c
device_release_driver+0x38/0x50
bus_remove_device+0x130/0x140
device_del+0x184/0x434
__scsi_remove_device+0x118/0x150
scsi_remove_target+0x1bc/0x240
sas_rphy_remove+0
crypto: ccp - Treat zero-length cert chain as query for blob lengths
In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Treat zero-length cert chain as query for blob lengths
When handling a PDH export, treat a zero-length userspace cert chain buffer
as a request to query the length of the relevant blobs. Failure to account
for the zero-length buffer trips a BUG_ON() when running with
CONFIG_DEBUG_VIRTUAL=y due to trying to get the physical address of the
ZERO_SIZE_PTR (returned by kzalloc() on the bogus allocation).
kernel BUG at arch/x86/mm/physaddr.c:28 !
Oops: invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 30 UID: 0 PID: 28580 Comm: syz.2.18 Kdump: loaded
Tainted
crypto: ccp/sev-dev-tsm - bail out early when pdev->bus is NULL
In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp/sev-dev-tsm - bail out early when pdev->bus is NULL
dsm_create() initially checks pdev->bus when computing segment_id:
u8 segment_id = pdev->bus ? pci_domain_nr(pdev->bus) : 0;
But the next two lines unconditionally dereference pdev->bus via
pcie_find_root_port() and especially pci_dev_id(pdev), which expands
to PCI_DEVID(dev->bus->number, dev->devfn). If pdev->bus is in fact
NULL, segment_id is initialised to 0 but the very next statement
crashes the kernel.
smatch flags this:
drivers/crypto/ccp/sev-dev-tsm.c:253 dsm_create() error: we
previously ass
In the Linux kernel, the following vulnerability has been resolved:
media: atomisp: gc2235: fix UAF and memory leak
gc2235_probe() handles its error paths incorrectly.
If media_entity_pads_init() fails, gc2235_remove() is called, which
tears down the subdev and frees dev, but then still falls through to
atomisp_register_i2c_module(). This results in use-after-free.
If atomisp_register_i2c_module() fails, the media entity and control
handler are left initialized and dev is leaked.
gc2235_remove() unconditionally calls media_entity_cleanup() and
v4l2_ctrl_handler_free(), but these are not initialized at every
error path in gc2235_probe().
firmware: arm_scmi: Fix OOB in scmi_power_name_get()
In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Fix OOB in scmi_power_name_get()
scmi_power_name_get() does not validate the domain number passed by the
external caller, which may lead to an out-of-bounds access.
Fix this by returning "unknown" for invalid domains, like
scmi_reset_name_get() does.
pinctrl: spacemit: fix NULL check in spacemit_pin_set_config
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: spacemit: fix NULL check in spacemit_pin_set_config
spacemit_pin_set_config() looks up the per-pin descriptor with
spacemit_get_pin() then checks the wrong variable for failure:
const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
...
if (!pin)
return -EINVAL;
reg = spacemit_pin_to_reg(pctrl, spin->pin);
pin is an unsigned int pin id, where 0 (GPIO_0 / gmac0_rxdv on K3) is a
valid pin, so rejecting it here drops the PAD config write for the first
pin of every group. On K3 Pico-ITX the GMAC RGMII group lists pin 0 as
its first entry, so its drive
In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix warning in poll cq direct mode
CQs allocated by ib_alloc_cq() always have a comp_handler. Though
in direct mode this handler is never expected to be called, it
is still called when the driver is reset, triggering the following
WARN_ONCE():
Call trace:
ib_cq_completion_direct+0x38/0x60
hns_roce_cq_completion+0x54/0x90 (hns_roce_hw_v2]
hns_roce_handle_device_err+Ox1c8/0x340 [hns_roce_hw_v2]
hns_roce_hw_v2_uninit_instance.constprop.0+0x34/0x70 [hns_roce_hw_v2]
hns_roce_hw_v2_reset_notify+0xc4/0xe0 [hns_roce_hw_v2]
hclge_notify_roce_client+0x60/0xbc [hclge]
hclge
ipv6: guard against possible NULL deref in __in6_dev_stats_get()
In the Linux kernel, the following vulnerability has been resolved:
ipv6: guard against possible NULL deref in __in6_dev_stats_get()
dev_get_by_index_rcu() could return NULL if the original physical
device is unregistered.
Found by Sashiko.
rapidio/tsi721: prevent a bad dereference in tsi721_db_dpc()
In the Linux kernel, the following vulnerability has been resolved:
rapidio/tsi721: prevent a bad dereference in tsi721_db_dpc()
With a list_for_each() loop, if we don't find the item we are looking for
in the list, then the loop exits with the iterator, which is "dbell" in
this loop, pointing to invalid memory.
This code uses the "found" variable to determine if we have found the
doorbell we are looking for or not. However, the problem that the "found"
variable needs to be set to false at the start of each iteration,
otherwise after the first correct doorbell, then everything is marked as
found.
Reset the "found" to false at the start o