ext4: drain in-flight DIO before buffered write fallback
In the Linux kernel, the following vulnerability has been resolved:
ext4: drain in-flight DIO before buffered write fallback
generic/746 started failing intermittently on ext3 (no-extent inodes).
The test triggers 'Page cache invalidation failure on direct I/O'
warnings and subsequent fsync returns -EIO. Adding a 50ms delay
between ext4_buffered_write_iter() and filemap_write_and_wait_range()
in ext4_dio_write_iter() makes the race almost always reproducible.
On no-extent inodes, DIO writes to holes cannot use unwritten extents,
so ext4_iomap_alloc() leaves m_flags=0 and ext4_map_blocks() returns 0.
The iomap layer then returns -ENOTBLK, c
ext4: use fsdata to track inline data write state and fix race
In the Linux kernel, the following vulnerability has been resolved:
ext4: use fsdata to track inline data write state and fix race
Instead of checking the live inode state (ext4_has_inline_data(inode)
and ext4_test_inode_state(inode, EXT4_STATE_MAY_INLINE_DATA)) in the
write_end handlers, use the fsdata parameter of the address space
operations to explicitly pass down the state in which write_begin
prepared the write.
A concurrent thread (such as ext4_page_mkwrite()) can convert the
inline data to an extent between write_begin and write_end. If this
happens, the write_end handlers would previously miss the inline
write_end path and fall th
ext4: validate readdir offset before accessing dirent
In the Linux kernel, the following vulnerability has been resolved:
ext4: validate readdir offset before accessing dirent
A corrupted directory can trigger the following KASAN report when
ext4_readdir() resumes from an invalid position:
BUG: KASAN: use-after-free in __ext4_check_dir_entry+0x5ef/0x820
Read of size 2 at addr ffff88810a646000 by task repro_linear/509
Call Trace:
<TASK>
dump_stack_lvl+0x53/0x70
print_report+0xd0/0x630
kasan_report+0xce/0x100
__ext4_check_dir_entry+0x5ef/0x820
ext4_readdir+0xcde/0x2b70
iterate_dir+0x1a1/0x520
__x64_sys_getdents64+0x12b/0x220
do_syscall_64+0xf9/0x540
entry_SY
wifi: ath6kl: avoid buffer overreads in WMI event handlers
In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: avoid buffer overreads in WMI event handlers
The following WMI event handlers currently read from the event buffer
without first verifying that the message was large enough to hold the
expected event:
ath6kl_wmi_scan_complete_rx()
ath6kl_wmi_addba_req_event_rx()
ath6kl_wmi_delba_req_event_rx()
Add length checks to prevent overread.
wifi: ath12k: Avoid buffer overread in ath12k_wmi_op_rx()
In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: Avoid buffer overread in ath12k_wmi_op_rx()
Currently, in ath12k_wmi_op_rx(), the firmware buffer is read without
first verifying that the buffer has enough data to hold a header. This
could result in a buffer overread.
Update the logic to verify the buffer contains at least enough data to
hold a wmi_cmd_hdr before reading from the buffer.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c7-00108-QCAHMTSWPL_V1.0_V2.0_SILICONZ_UPSTREAM-3
wifi: ath11k: Avoid buffer overread in ath11k_wmi_tlv_op_rx()
In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: Avoid buffer overread in ath11k_wmi_tlv_op_rx()
Currently, in ath11k_wmi_tlv_op_rx(), the firmware buffer is read
without first verifying that the buffer has enough data to hold a
header. This could result in a buffer overread.
Add an upfront length check before dereferencing skb->data as a
wmi_cmd_hdr. The check is placed before the trace_ath11k_wmi_event()
call to preserve the existing trace semantics (tracing the full raw
WMI event including the header), unlike the analogous ath12k fix which
could use skb_pull_data() directly.
Compile tested only.
RDMA/bnxt_re: Clear VM_MAYWRITE on DBR/toggle page mmap
In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Clear VM_MAYWRITE on DBR/toggle page mmap
bnxt_re_mmap() rejects VM_WRITE for the DBR_PAGE and TOGGLE_PAGE mmap
flags, but a read-only mapping can still retain VM_MAYWRITE. nd later
be upgraded with mprotect(PROT_WRITE). This can bypass the write check
that only runs at mmap time.
Clear VM_MAYWRITE before vm_insert_page() in the shared DBR/toggle-page
branch, matching the existing policy that userspace writes are not
expected for these pages.
ext4: fix buffer_head leak in ext4_init_orphan_info
In the Linux kernel, the following vulnerability has been resolved:
ext4: fix buffer_head leak in ext4_init_orphan_info
ext4_init_orphan_info() reads orphan file blocks with ext4_bread()
and stores the returned buffer_head in oi->of_binfo[i].ob_bh.
If ext4_bread() succeeds but the orphan block magic or checksum
validation fails, the function jumps to out_free. However, the old
out_free loop starts releasing buffers from i - 1, so the current
buffer_head at index i is skipped.
This leaks the buffer_head reference obtained by ext4_bread() on the
bad magic and bad checksum error paths.
Fix this by tracking the number of successfully read bu
cpufreq: amd-pstate-ut: Skip tests when amd-pstate driver is not active
In the Linux kernel, the following vulnerability has been resolved:
cpufreq: amd-pstate-ut: Skip tests when amd-pstate driver is not active
The crash issue may occur when modprobe amd_pstate_ut on intel platform.
amd_pstate_ut: 1 amd_pstate_ut_acpi_cpc_valid success!
amd_pstate_ut: 2 amd_pstate_ut_check_enabled success!
BUG: kernel NULL pointer dereference, address: 0000000000000080
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 0 PID: 20300 Comm: modprobe
Kdump: loaded Tainted: G O 6.6.0-0010.rc1.ctl4.x86_64 #1
Hardware
firmware: arm_scmi: Unrequest devices if driver registration fails
In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Unrequest devices if driver registration fails
scmi_driver_register() requests protocol devices before registering the
driver. If driver_register() fails, those requests remain in the global
IDR and retain pointers to the module's ID table. Once the failed module
load releases that storage, later request matching or SCMI device creation
can dereference the stale pointers.
Unrequest the complete protocol table before returning the registration
failure. At this point table registration succeeded, so every entry is
owned by the current registration attempt
xfrm: Fix skb double-free in xfrm_dev_direct_output()
In the Linux kernel, the following vulnerability has been resolved:
xfrm: Fix skb double-free in xfrm_dev_direct_output()
A return value other than 1 from local_out() means that the skb has been
consumed or its ownership was transferred. xfrm_dev_direct_output()
nevertheless frees the skb on this path, causing a double-free when
netfilter drops the packet and invalidating any other owner.
Return the local_out() result directly, matching the ownership handling
in xfrm_output_resume().
RDMA/erdma: complete object teardown when the destroy command fails
In the Linux kernel, the following vulnerability has been resolved:
RDMA/erdma: complete object teardown when the destroy command fails
erdma_destroy_qp(), erdma_destroy_cq(), erdma_dereg_mr(), and
erdma_destroy_ah() returned early when erdma_post_cmd_wait() failed,
leaking the queue buffers, MTTs, doorbells and the STAG, QPN, CQN and AHN
identifiers. A command timeout clears ERDMA_CMDQ_STATE_OK_BIT and
permanently disables the command queue, so no retry can succeed; the RDMA
core keeps the object after a failed destructor and forced uverbs cleanup
then nulls the pointers, making the resources unreachable.
Warn on failure but release every
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix WARNING in bpf_tracing_link_release
The trampoline could be corrupted by the blindly
'tr->flags = BPF_TRAMP_F_TAIL_CALL_CTX' in verifier.
1. A fexit attached to a tail_call_reachable prog. 'tr->flags' became
'BPF_TRAMP_F_CALL_ORIG | BPF_TRAMP_F_TAIL_CALL_CTX'. And, the
trampoline would poke the target prog's nop insn using jmp insn instead
of call insn.
2. Another fexit loaded with the same tail_call_reachable prog target.
'tr->flags' became 'BPF_TRAMP_F_TAIL_CALL_CTX'.
3. Close the first fexit link. Due to no BPF_TRAMP_F_CALL_ORIG in
'tr->flags', t
cxl/region: Fix use-after-free in find_pos_and_ways() error path
In the Linux kernel, the following vulnerability has been resolved:
cxl/region: Fix use-after-free in find_pos_and_ways() error path
The error path releases its reference to a switch decoder before
logging an error that includes the decoder name. If the released
reference is the last one, the decoder can be freed before the error
message accesses its name.
Drop the reference after the error is reported.
pinctrl: mediatek: use devm_gpiochip_add_data() for GPIO chip
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: use devm_gpiochip_add_data() for GPIO chip
The gpio_chip is allocated with device-managed memory but registered with
the non-managed gpiochip_add_data(). This was harmless while the drivers
were built-in, but once they can be built as modules and unbound/rmmod'd,
devm frees the gpio_chip's memory while it is still registered, causing a
use-after-free.
Register it with devm_gpiochip_add_data() so it shares the same
device-managed lifecycle, which also lets the manual gpiochip_remove()
error paths go away.
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: mediatek: free EINT resources on unbind
mtk_eint_do_init() creates an IRQ domain, populates it with a mapping for
every EINT line and installs a chained handler on the parent interrupt,
but none of these are ever released. This was harmless while the drivers
were built-in, but now that they can be built as modules and
unbound/rmmod'd it leaves behind a dangling IRQ domain, interrupt mappings
whose chip data points at freed memory, and a chained handler that keeps
firing into that freed data.
The plain allocations in mtk_eint_do_init() already use the device-manage
In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: core: Validate string descriptors
The string descriptor length includes a two-byte header while the UTF-16
payload starts after it. utf16s_to_utf8s() expects a count of UTF-16 code
units, not bytes. Passing the payload byte count can make it read beyond
the descriptor buffer.
Validate that the payload has an even byte count, pass a code-unit count to
the converter, and allocate sufficient UTF-8 output space.
The raw string buffer starts after the descriptor header but its size is
bLength. Copying bLength bytes from that pointer can read beyond the
response buff
scsi: ufs: debugfs: Reserve space for a string terminator
In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: debugfs: Reserve space for a string terminator
ufs_saved_err_write() copies user input into a zero-initialized stack
buffer and passes it to kstrtoint(). A write that fills the entire buffer
overwrites its only terminator.
Reject an input whose length leaves no room for the trailing NUL.
crypto: keembay - Initialize completion before requesting IRQ
In the Linux kernel, the following vulnerability has been resolved:
crypto: keembay - Initialize completion before requesting IRQ
kmb_ocs_aes_probe() requests the device IRQ before initializing
irq_completion. Once the handler is registered it can run immediately,
and ocs_aes_irq_handler() unconditionally calls complete(). An
interrupt in this window would therefore use an uninitialized
completion.
Initialize the completion before requesting the IRQ, as the sibling
OCS HCU and ECC drivers already do.
RDMA/mlx5: Fix integer overflow of user QP buffer size
In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix integer overflow of user QP buffer size
set_user_buf_size() computes the QP buffer size by left-shifting the
user-supplied rq.wqe_cnt and rq.wqe_shift values as signed integers.
A sufficiently large rq.wqe_cnt causes signed integer overflow, which
is undefined behavior, and yields a small or negative buf_size, causing
ib_umem_get() to map a buffer smaller than the hardware will actually
write into.
Replace the shifts and addition with check_shl_overflow() and
check_add_overflow(), rejecting invalid user inputs.
Moreover, guard the identical shift computing