udf: Mark LVID buffer as uptodate before marking it dirty
In the Linux kernel, the following vulnerability has been resolved:
udf: Mark LVID buffer as uptodate before marking it dirty
When an I/O error occurs while writing the Logical Volume Integrity
Descriptor (LVID) buffer to the block device, the block layer's completion
handler (`end_buffer_write_sync()`) clears the `BH_Uptodate` flag on the
buffer. However, the buffer still contains valid LVID data in memory. If
the filesystem is subsequently remounted read-write or synced,
`udf_open_lvid()` or `udf_sync_fs()` will modify the LVID buffer and call
`mark_buffer_dirty()`. This triggers a spurious
`WARN_ON_ONCE(!buffer_uptodate(bh))` warning in
bpf: Fix vmlinux BTF prep race in bpf_get_btf_vmlinux
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix vmlinux BTF prep race in bpf_get_btf_vmlinux
bpf_get_btf_vmlinux() lazily parses the vmlinux BTF under the
bpf_verifier_lock, but publishes the result through a plain store
and re-checks it through a plain lockless load. Nothing orders
the stores initializing the struct btf inside btf_parse_vmlinux()
against the store publishing the pointer: On a weakly ordered
arch, a concurrent first-time caller taking the lockless fast
path could in principle observe the pointer before the parsed
contents are visible. The mutex_unlock() does not help such a
reader given it only
bpf: Fix use-after-free on mm_struct in bpf_find_vma()
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix use-after-free on mm_struct in bpf_find_vma()
bpf_find_vma() reads task->mm and calls mmap_read_trylock(mm) without
holding a reference on the mm. On a foreign task, a concurrent exit_mm()
can free the mm_struct between the lockless read and the trylock,
resulting in a use-after-free. mm_struct is not SLAB_TYPESAFE_BY_RCU.
For the current task, task->mm is stable. For a foreign task, pin the mm
under task->alloc_lock and release it with mmput_async(), mirroring commit
d8e27d2d22b6 ("bpf: fix mm lifecycle in open-coded task_vma iterator").
Use spin_trylock() instea
bus: mhi: ep: Fix device refcount leak in the error path of MHI device creation
In the Linux kernel, the following vulnerability has been resolved:
bus: mhi: ep: Fix device refcount leak in the error path of MHI device creation
mhi_ep_create_device() takes one device reference for the UL channel and
another for the DL channel after allocating the transfer device. These
references are normally released by mhi_ep_destroy_device() before the
device itself is removed.
If dev_set_name() or device_add() fails, the error path currently drops
only one reference. The remaining channel references keep the device
from being released and leave the channels associated with a device that
was never registered.
Route both failures t
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-privacy: Fix race condition
Accessing priv->features_present needs to happen with the list mutex
being held, otherwise priv can be freed at any moment.
platform/x86: dell-wmi-base: Fix resource leak on module load failure
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-base: Fix resource leak on module load failure
We need to properly clean up the SMBIOS request and the privacy driver
when the module load fails.
platform/x86: dell-wmi-base: Fix handling of ultra performance key
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-base: Fix handling of ultra performance key
The commit message of commit 5fbd827eb9c2 ("platform/x86: dell-wmi: Recognise or support new switches")
states that the ultra performance key contains additional data
after the type and code fields. The event data passed to
dell_wmi_process_key() is already parsed, so "buffer" already
starts after those two fields.
Use the correct index for accessing the first data field to avoid
a potential buffer overread.
platform/x86: lg-laptop: Fix LED resource handling
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: lg-laptop: Fix LED resource handling
The event notification callback might access kbd_backlight even
when it was not successfully registered with the LED subsystem.
The same happens inside acpi_remove(), where the LED devices are
unregistered unconditionally.
Fix this by tracking the availability of the kbd_backlight LED
device and use devm_led_classdev_register() to let devres take
care of unregistering the LED devices during removal. For this
the parent device of the LED devices is changed to the native
platform device.
remoteproc: qcom_q6v5_adsp: Fix reference leak for device node
In the Linux kernel, the following vulnerability has been resolved:
remoteproc: qcom_q6v5_adsp: Fix reference leak for device node
When calling of_parse_phandle_with_args(), the caller is responsible
to call of_node_put() to release the reference of device node.
In adsp_map_carveout, it does not release the reference.
bpf: Reject rdonly/rdwr_buf_size kfunc arguments that exceed u32 max
In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject rdonly/rdwr_buf_size kfunc arguments that exceed u32 max
check_kfunc_args() detects a kfunc argument named rdonly_buf_size or
rdwr_buf_size and stores reg->var_off.value into meta->r0_size, a u64,
and does not bound it. check_kfunc_call() later copies that value into
the returned register's mem_size field:
meta->r0_size = reg->var_off.value;
...
regs[BPF_REG_0].mem_size = meta.r0_size;
regs[BPF_REG_0].mem_size is u32. A constant whose upper 32 bits are set
gets truncated instead of causing a load-time rejection, so the verifier
records a PTR_TO_MEM regis
serial: qcom-geni: do not advance stale DMA completions
In the Linux kernel, the following vulnerability has been resolved:
serial: qcom-geni: do not advance stale DMA completions
The qcom GENI serial DMA TX completion path advances the transmit fifo by
the number of bytes recorded in port->tx_remaining.
If uart_flush_buffer() runs after the hardware has completed a DMA
transfer but before the DMA completion interrupt has been handled, the
serial core resets the transmit fifo while port->tx_remaining still
describes the old DMA transfer.
A previous fix avoided advancing an empty fifo by checking that the fifo
length is at least tx_remaining. That still does not distinguish the old
DMA payload
usb: gadget: uac: validate rate list length before storing
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uac: validate rate list length before storing
UAC1 and UAC2 configfs rate-list attributes parse a comma-separated
list of sampling rates and store each parsed value in fixed-size arrays.
The arrays have UAC_MAX_RATES entries, but the store paths do not check
that the input contains at most that many tokens before writing through
opts->name##s[i++].
Writing more than ten rates therefore writes past the end of the
p_srates[] or c_srates[] array in struct f_uac1_opts or struct
f_uac2_opts.
With CONFIG_UBSAN_BOUNDS enabled, writing an 11-entry rate list to the
UA
usb: gadget: configfs: fix out-of-bounds read of qw_sign
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: configfs: fix out-of-bounds read of qw_sign
os_desc_qw_sign_show() passes OS_STRING_QW_SIGN_LEN as the input
length to utf16s_to_utf8s(), but that argument counts UTF-16 code
units while OS_STRING_QW_SIGN_LEN (14) is the byte size of qw_sign[].
The array holds only OS_STRING_QW_SIGN_LEN / 2 (7) code units, so the
conversion reads up to 7 units (14 bytes) past the end of qw_sign[]
into the following members of struct gadget_info when the stored
signature fills the array without a NUL terminator, exposing those
bytes through the configfs attribute.
The store pat
usb: ljca: bound bank_num in ljca_enumerate_gpio()
In the Linux kernel, the following vulnerability has been resolved:
usb: ljca: bound bank_num in ljca_enumerate_gpio()
ljca_enumerate_gpio() reads desc->bank_num from the device and loops
valid_pin[i] = get_unaligned_le32(...) for i < bank_num. valid_pin[]
holds only LJCA_MAX_GPIO_NUM / 32 = 2 entries.
Two checks run before the loop. The reply length must match
struct_size(desc, bank_desc, bank_num). The product
pins_per_bank * bank_num must not exceed LJCA_MAX_GPIO_NUM. Neither one
bounds bank_num against the size of valid_pin[]. The reply is capped at
LJCA_MAX_PAYLOAD_SIZE (60) bytes, so the struct_size check limits
bank_num to 9. A devi
In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: aspeed_udc: check endpoint DMA allocation
ast_udc_probe() allocates a coherent DMA buffer used as the backing store
for endpoint buffers. ast_udc_init_ep() derives per-endpoint buffer
pointers from udc->ep0_buf, so a failed allocation is dereferenced during
probe.
Check the allocation before endpoint setup. The existing probe error path
called ast_udc_remove(), which unregisters the gadget unconditionally and
is not safe before usb_add_gadget_udc() succeeds. Add a local cleanup
helper for probe failures so pre-registration failures only unwind the
resources th
usb: fix UAF when probe runs concurrent to dyn ID removal
In the Linux kernel, the following vulnerability has been resolved:
usb: fix UAF when probe runs concurrent to dyn ID removal
Dynamic IDs are only guaranteed to be valid when usb_dynids_lock is held,
as remove_id_store can free the node. Thus, make a copy in
usb_probe_interface. Clarify the documentation that the id parameter is
only valid during the probe.
USB serial has the same pattern, but it does not need fixing as the IDs
cannot be removed via sysfs.
platform/x86: asus-wmi: fix resource leaks on probe failure
In the Linux kernel, the following vulnerability has been resolved:
platform/x86: asus-wmi: fix resource leaks on probe failure
During driver initialization in asus_wmi_add(), various subsystems are
registered sequentially. However, the error path labels are out of order
relative to the registration sequence.
Specifically:
1. If asus_wmi_custom_fan_curve_init() fails, the driver jumps to
fail_custom_fan_curve. Because this label is placed below fail_sysfs,
it bypasses the cleanup calls for the input device and sysfs groups,
which were successfully registered before, leaking those resources.
2. If asus_screenpad_init() fails, the d
platform/mellanox: mlxbf-pmc: Check ACPI_COMPANION() against NULL
In the Linux kernel, the following vulnerability has been resolved:
platform/mellanox: mlxbf-pmc: Check ACPI_COMPANION() against NULL
Every platform driver can be forced to match a device that doesn't match
its list of device IDs because of device_match_driver_override(), so
platform drivers that rely on the existence of a device's ACPI companion
object need to verify its presence.
mlxbf_pmc_probe() passes the result of ACPI_COMPANION() to
acpi_device_hid(), which dereferences it, so force-binding the driver to
a device without an ACPI companion leads to a NULL pointer dereference.
Accordingly, add a requisite ACPI_COMPANION() check again
platform/surface: acpi-notify: Check ACPI companion before use
In the Linux kernel, the following vulnerability has been resolved:
platform/surface: acpi-notify: Check ACPI companion before use
Since every platform driver can be forced to match a device that doesn't
match its list of device IDs because of device_match_driver_override(),
platform drivers that rely on the existence of a device's ACPI companion
object should verify its presence.
san_probe() dereferences the result of ACPI_COMPANION() when installing
the GSBUS address space handler, so force-binding the driver to a device
without an ACPI companion leads to a NULL pointer dereference. The
dereference was introduced when the probe function
In the Linux kernel, the following vulnerability has been resolved:
clk: qcom: camcc-sc8280xp: unregister CAMCC_GDSC_CLK
With the introduction of sync_state support in the clk and pmdomain
subsystems, the following warning happens when the unused clocks are
shutdown in camcc-sc8280xp:
[ 15.408367] titan_top_gdsc status stuck at 'on'
[ 15.408429] WARNING: drivers/clk/qcom/gdsc.c:178 at gdsc_toggle_logic+0x14c/0x160, CPU#2: kworker/u32:1/14
[ 15.408462] Modules linked in: bnep vfat fat ath11k_pci(+) ath11k mac80211 cfg80211 mhi libarc4 snd_soc_wcd938x snd_soc_wcd938x_sdw snd_soc_wcd_classh hci_uart snd_soc_wcd_common
sn