PatchFirst · Latest vulnerabilities
Vulnerabilities published for linux-6.12 in the last 30 days: 483. Listed in the KEV catalogue: 0.
Vulnerabilities: 2889
In the Linux kernel, the following vulnerability has been resolved: platform/x86: dell-wmi-base: Fix resource leak on module load failure We need to properly clean up the SMBIOS request and the privacy driver when the module load fails.
In the Linux kernel, the following vulnerability has been resolved: platform/x86: lg-laptop: Fix LED resource handling The event notification callback might access kbd_backlight even when it was not successfully registered with the LED subsystem. The same happens inside acpi_remove(), where the LED devices are unregistered unconditionally. Fix this by tracking the availability of the kbd_backlight LED device and use devm_led_classdev_register() to let devres take care of unregistering the LED devices during removal. For this the parent device of the LED devices is changed to the native platform device.
In the Linux kernel, the following vulnerability has been resolved: remoteproc: qcom_q6v5_adsp: Fix reference leak for device node When calling of_parse_phandle_with_args(), the caller is responsible to call of_node_put() to release the reference of device node. In adsp_map_carveout, it does not release the reference.
In the Linux kernel, the following vulnerability has been resolved: serial: qcom-geni: do not advance stale DMA completions The qcom GENI serial DMA TX completion path advances the transmit fifo by the number of bytes recorded in port->tx_remaining. If uart_flush_buffer() runs after the hardware has completed a DMA transfer but before the DMA completion interrupt has been handled, the serial core resets the transmit fifo while port->tx_remaining still describes the old DMA transfer. A previous fix avoided advancing an empty fifo by checking that the fifo length is at least tx_remaining. That still does not distinguish the old DMA payload
In the Linux kernel, the following vulnerability has been resolved: usb: gadget: f_fs: Fix fence cleanup in ffs_dmabuf_transfer() error paths The error paths for endpoint-disabled (ESHUTDOWN) and request-allocation failure (ENOMEM) in ffs_dmabuf_transfer() jump to err_fence_put which calls dma_fence_put() on the fence. However, at that point the fence has only been kmalloc'd — dma_fence_init() has not been called yet, so the refcount and the fence ops are uninitialized. Calling dma_fence_put() on such an object leads to undefined behavior. Use kfree() instead, since the fence is just a plain allocation at this stage, and rename the label t
In the Linux kernel, the following vulnerability has been resolved: usb: gadget: configfs: fix out-of-bounds read of qw_sign os_desc_qw_sign_show() passes OS_STRING_QW_SIGN_LEN as the input length to utf16s_to_utf8s(), but that argument counts UTF-16 code units while OS_STRING_QW_SIGN_LEN (14) is the byte size of qw_sign[]. The array holds only OS_STRING_QW_SIGN_LEN / 2 (7) code units, so the conversion reads up to 7 units (14 bytes) past the end of qw_sign[] into the following members of struct gadget_info when the stored signature fills the array without a NUL terminator, exposing those bytes through the configfs attribute. The store pat
In the Linux kernel, the following vulnerability has been resolved: usb: ljca: bound bank_num in ljca_enumerate_gpio() ljca_enumerate_gpio() reads desc->bank_num from the device and loops valid_pin[i] = get_unaligned_le32(...) for i < bank_num. valid_pin[] holds only LJCA_MAX_GPIO_NUM / 32 = 2 entries. Two checks run before the loop. The reply length must match struct_size(desc, bank_desc, bank_num). The product pins_per_bank * bank_num must not exceed LJCA_MAX_GPIO_NUM. Neither one bounds bank_num against the size of valid_pin[]. The reply is capped at LJCA_MAX_PAYLOAD_SIZE (60) bytes, so the struct_size check limits bank_num to 9. A devi
In the Linux kernel, the following vulnerability has been resolved: usb: gadget: aspeed_udc: check endpoint DMA allocation ast_udc_probe() allocates a coherent DMA buffer used as the backing store for endpoint buffers. ast_udc_init_ep() derives per-endpoint buffer pointers from udc->ep0_buf, so a failed allocation is dereferenced during probe. Check the allocation before endpoint setup. The existing probe error path called ast_udc_remove(), which unregisters the gadget unconditionally and is not safe before usb_add_gadget_udc() succeeds. Add a local cleanup helper for probe failures so pre-registration failures only unwind the resources th
In the Linux kernel, the following vulnerability has been resolved: usb: fix UAF when probe runs concurrent to dyn ID removal Dynamic IDs are only guaranteed to be valid when usb_dynids_lock is held, as remove_id_store can free the node. Thus, make a copy in usb_probe_interface. Clarify the documentation that the id parameter is only valid during the probe. USB serial has the same pattern, but it does not need fixing as the IDs cannot be removed via sysfs.
In the Linux kernel, the following vulnerability has been resolved: platform/mellanox: mlxbf-pmc: Check ACPI_COMPANION() against NULL Every platform driver can be forced to match a device that doesn't match its list of device IDs because of device_match_driver_override(), so platform drivers that rely on the existence of a device's ACPI companion object need to verify its presence. mlxbf_pmc_probe() passes the result of ACPI_COMPANION() to acpi_device_hid(), which dereferences it, so force-binding the driver to a device without an ACPI companion leads to a NULL pointer dereference. Accordingly, add a requisite ACPI_COMPANION() check again
In the Linux kernel, the following vulnerability has been resolved: platform/surface: acpi-notify: Check ACPI companion before use Since every platform driver can be forced to match a device that doesn't match its list of device IDs because of device_match_driver_override(), platform drivers that rely on the existence of a device's ACPI companion object should verify its presence. san_probe() dereferences the result of ACPI_COMPANION() when installing the GSBUS address space handler, so force-binding the driver to a device without an ACPI companion leads to a NULL pointer dereference. The dereference was introduced when the probe function
In the Linux kernel, the following vulnerability has been resolved: clk: qcom: camcc-sc8280xp: unregister CAMCC_GDSC_CLK With the introduction of sync_state support in the clk and pmdomain subsystems, the following warning happens when the unused clocks are shutdown in camcc-sc8280xp: [ 15.408367] titan_top_gdsc status stuck at 'on' [ 15.408429] WARNING: drivers/clk/qcom/gdsc.c:178 at gdsc_toggle_logic+0x14c/0x160, CPU#2: kworker/u32:1/14 [ 15.408462] Modules linked in: bnep vfat fat ath11k_pci(+) ath11k mac80211 cfg80211 mhi libarc4 snd_soc_wcd938x snd_soc_wcd938x_sdw snd_soc_wcd_classh hci_uart snd_soc_wcd_common sn
In the Linux kernel, the following vulnerability has been resolved: RDMA/core: Wait for RCU callbacks before unloading ib_core put_gid_ndev() is queued with call_rcu() and implemented in ib_core. Stopping the workqueues does not drain callbacks already queued, so RCU could invoke it after the module code has been unloaded. synchronize_rcu() does not wait for callbacks. Wait for them after all producers have stopped.
In the Linux kernel, the following vulnerability has been resolved: RDMA/mlx5: Drain RCU callbacks during module teardown devx_free_subscription() can remain queued after the last DevX event file drops its module reference or an auxiliary driver detaches its devices. mlx5_ib can then unload before the callback runs. Registration error unwind has the same risk because driver registration can attach existing devices before failing. Wait after all drivers have stopped.
In the Linux kernel, the following vulnerability has been resolved: RDMA/ipoib: Drain RCU callbacks during module teardown IPoIB reclamation completions can be signaled from inside an RCU callback. Teardown can wake before the callback returns and unload ib_ipoib while its code is still executing. Client registration failure can also remove already-added devices and queue callbacks. Wait after client and workqueue teardown.
In the Linux kernel, the following vulnerability has been resolved: RDMA/rxe: Avoid reprocessing the current packet after the QP enters the error state When do_complete() finds the QP in the error state it returns RESPST_CHK_RESOURCE. Before commit 49dc9c1f0c7e ("RDMA/rxe: Cleanup reset state handling in rxe_resp.c") this was the flush loop: check_resource() had an error-state branch that fetched each remaining recv WQE and completed it with IB_WC_WR_FLUSH_ERR, without touching the current packet. That commit removed the error-state branch from check_resource() (draining is now done at rxe_receiver() entry) but kept the do_complete() erro
In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Preserve unit 0 on allocation failure hfi1_free_devdata() assumes that the device was inserted into the unit table and unconditionally erases dd->unit. If xa_alloc_irq() fails, the zero-initialized unit remains zero, so full cleanup can remove an unrelated device from index 0. Release only the rdmavt allocation and return immediately while the unit table has not acquired the device.
In the Linux kernel, the following vulnerability has been resolved: RDMA/hfi1: Free RX data on late probe failure hfi1_init_dd() allocates the shared AIP/VNIC RX support before returning. If hfi1_init() or hfi1_register_ib_device() later fails, init_one() tears down the device data without calling hfi1_free_rx(). This leaks netdev_rx and its dummy netdev. Free the RX support after IB unregistration and before postinit_cleanup(), as done on normal device removal.
In the Linux kernel, the following vulnerability has been resolved: media: v4l2-async: Unregister sub-device if asc_list is empty When my em28xx USB device that uses the i2c tvp5150 driver is disconnected, it crashes. The cause is that the tvp5150 i2c module uses v4l2_async, but the em28xx driver does not since it predates v4l2_async. In that corner case sd->asc_list is empty, so v4l2_async_unregister_subdev() never calls v4l2_device_unregister_subdev(). Modify the code so that, if sd->asc_list is empty, v4l2_device_unregister_subdev() is still called.
In the Linux kernel, the following vulnerability has been resolved: rpmsg: glink: fix deadlock in endpoint destroy during driver detach During driver detach, the device core holds the device mutex throughout the driver's remove callback chain. When the rpmsg endpoint is destroyed as part of that teardown, the GLINK endpoint destroy implementation attempts to unregister the underlying rpmsg device. That unregistration calls device_del(), which tries to re-acquire the same device mutex already held higher up the stack, causing rmmod to hang indefinitely. The deadlock manifests with the following call chain: [<0>] device_del+0x44/0x414 <-
Check your installed stack and versions against the current vulnerability feeds.